- 您現在的位置：買賣IC網 > PDF目錄1988 > AD9879BSZ (Analog Devices Inc)IC PROCESSOR FRONT END 100MQFP PDF資料下載
參數資料
| 型號： | AD9879BSZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 19/32頁 |
| 文件大小： | 0K |
| 描述： | IC PROCESSOR FRONT END 100MQFP |
| 標準包裝： | 1 |
| 位數： | 12 |
| 通道數： | 5 |
| 功率（瓦特）： | 587mW |
| 電壓 - 電源，模擬： | 3.3V |
| 電壓 - 電源，數字： | 3.3V |
| 封裝/外殼： | 100-BQFP |
| 供應商設備封裝： | 100-MQFP（14x20） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
AD9879
Rev. A | Page 26 of 32
PROGRAMMING THE AD8321/AD8323 OR AD8322/AD8327 CABLE DRIVER AMPLIFIER
GAIN CONTROL
Programming the gain of the AD832x family of cable driver
amplifiers can be accomplished via the AD9879 cable amplifier
control interface. Four 8-bit registers within the AD9879 (one
per profile) store the gain value to be written to the serial 3-wire
port. Typically, either the AD8321/AD8323 or AD8322/AD8327
variable gain cable amplifiers are connected to the chip’s 3-wire
cable amplifier interface. The Tx gain control select bit in
Register 0x0F changes the interpretation of the bits in Registers
0x13, 0x17, 0x1B, and 0x1F. See the Cable Driver Gain Control
section register description.
Data transfers to the gain programmable cable driver amplifier
are initiated by the following four conditions.
1.
Power-Up and Hardware Reset—Upon initial power-up
and every hardware reset, the AD9879 clears the contents
of the gain control registers to 0, which defines the lowest
gain setting of the AD832x. Thus, the AD9879 writes all 0s
out of the 3-wire cable amplifier control interface.
2.
Software Reset—Writing a 1 to Bit 5 of Address 0x00
initiates a software reset. Upon a software reset, the
AD9879 clears the contents of the gain control registers to
0 for the lowest gain and sets the profile select to 0. The
AD9879 writes all 0s out of the 3-wire cable amplifier
control interface if the gain was previously on a different
setting (other than 0).
3.
Change in Profile Selection—The AD9879 samples the
PROFILE input pin together with the two profile select bits
and writes to the AD832x gain control registers when a
change in profile and gain is determined. The data written
to the cable driver amplifier comes from the AD9879 gain
control register associated with the current profile.
4.
Write to AD9879 Cable Driver Amplifier Control
Registers—The AD9879 writes gain control data associated
with the current profile to the AD832x whenever the
selected AD9879 cable driver amplifier gain setting is
changed.
Once a new stable gain value is detected (48 MCLK to
64 MCLK cycles after initiation), a data write starts with
CA_EN going low. The AD9879 always finishes a write
sequence to the cable driver amplifier once it is started. The
logic controlling data transfers to the cable driver amplifier uses
up to 200 MCLK cycles and is designed to prevent erroneous
write cycles from occurring.
相關PDF資料 |
PDF描述 |
|---|---|
| AD9901KQ | IC PHASE/FREQ DISCRIMR 14-CDIP |
| AD9920ABBCZRL | IC PROCESSOR CCD 12BIT 105CSPBGA |
| AD9978BCPZRL | IC PROCESSOR CCD 14BIT 40-LFCSP |
| ADADC71KD | IC ADC 16BIT HIGH RES 32-CDIP |
| ADADC80-Z-12 | IC ADC 12BIT INTEGRATED 32-CDIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9879BSZKL1 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| AD9879-EB | 制造商:Analog Devices 功能描述:Evaluation Board For Mixed Signal Front End Set Top Box, Cable Modem 制造商:Analog Devices 功能描述:DEV TOOLS, MIXED SGNL FRONT END SET TOP , CBL MODEM - Bulk |
| AD9880 | 制造商:Analog Devices 功能描述:AUDIO PROCESSOR - Bulk |
| AD9880/PCB | 制造商:AD 制造商全稱:Analog Devices 功能描述:Analog/HDMI Dual Display Interface |
| AD9880/PCBZ | 功能描述:KIT EVALUATION AD9880 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:Advantiv® 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
發布緊急采購，3分鐘左右您將得到回復。