- 您現在的位置：買賣IC網 > PDF目錄1893 > AD9755ASTZRL (Analog Devices Inc)IC DAC 14BIT 300MSPS 48-LQFP PDF資料下載
參數資料
| 型號： | AD9755ASTZRL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 8/28頁 |
| 文件大小： | 0K |
| 描述： | IC DAC 14BIT 300MSPS 48-LQFP |
| 產品培訓模塊： | Data Converter Fundamentals DAC Architectures |
| 標準包裝： | 2,000 |
| 系列： | TxDAC+® |
| 設置時間： | 11ns |
| 位數： | 14 |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 電壓電源： | 模擬和數字 |
| 功率耗散（最大）： | 165mW |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-LQFP |
| 供應商設備封裝： | 48-LQFP（7x7） |
| 包裝： | 帶卷 (TR) |
| 輸出數目和類型： | 2 電流，單極；2 電流，雙極 |
| 采樣率（每秒）： | 300M |
| 配用： | AD9755-EB-ND - BOARD EVAL FOR AD9755 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
REV. B
AD9755
–16–
IOUTFS (mA)
40
20
0
20.0
10.0
0
I AVDD
(mA)
35
10
30
25
15
5
2.5
5.0
7.5
12.5
15.0
17.5
Figure 17. IAVDD vs. IOUTFS
RATIO (
fOUT/fDAC)
20
16
0
1
0.01
0.001
I DVDD
(mA)
18
14
12
10
8
6
4
2
0.1
300MSPS
200MSPS
100MSPS
50MSPS
25MSPS
Figure 18. IDVDD vs. fOUT/fDAC Ratio
fDAC (MHz)
10
0
300
150
0
PLL_V
DD
(mA)
9
8
7
6
5
4
3
2
50
100
200
250
1
175
25
75
125
225
275
DIV SETTING 00
DIV SETTING 11
DIV SETTING 10
DIV SETTING 01
Figure 19. PLLVDD vs. fDAC
APPLYING THE AD9755
OUTPUT CONFIGURATIONS
The following sections illustrate some typical output configurations
for the AD9755. Unless otherwise noted, it is assumed that IOUTFS
is set to a nominal 20 mA. For applications requiring the optimum
dynamic performance, a differential output configuration is
suggested. A differential output configuration may consist of
either an RF transformer or a differential op amp configuration.
The transformer configuration provides the optimum high
frequency performance and is recommended for any application
allowing for ac coupling. The differential op amp configuration
is suitable for applications requiring dc coupling, a bipolar output,
signal gain, and/or level-shifting within the bandwidth of the
chosen op amp.
A single-ended output is suitable for applications requiring a
unipolar voltage output. A positive unipolar output voltage will
result if IOUTA and/or IOUTB are connected to an appropriately
sized load resistor, RLOAD, referred to ACOM. This configuration
may be more suitable for a single-supply system requiring a dc-
coupled, ground referred output voltage. Alternatively, an amplifier
could be configured as an I-V converter, thus converting IOUTA or
IOUTB into a negative unipolar voltage. This configuration provides
the best dc linearity since IOUTA or IOUTB is maintained at a virtual
ground. Note that IOUTA provides slightly better performance
than IOUTB.
DIFFERENTIAL COUPLING USING A TRANSFORMER
An RF transformer can be used to perform a differential-to-
single-ended signal conversion, as shown in Figure 20. A
differentially-coupled transformer output provides the optimum
distortion performance for output signals whose spectral content
lies within the transformer’s pass band. An RF transformer such
as the Mini-Circuits T1–1T provides excellent rejection of
common-mode distortion (i.e., even-order harmonics) and
noise over a wide frequency range. When IOUTA and IOUTB are
terminated to ground with 50
, this configuration provides
0dBm power to a 50
load on the secondary with a DAC full-
scale current of 20 mA. A 2:1 transformer such as the Coilcraft
WB2040-PC can also be used in a configuration in which IOUTA
and IOUTB are terminated to ground with 75
. This configuration
improves load matching and increases power to 2 dBm into a
50
load on the secondary. Transformers with different imped-
ance ratios may also be used for impedance matching purposes.
Note that the transformer provides ac coupling only.
The center tap on the primary side of the transformer must be
connected to ACOM to provide the necessary dc current path for
both IOUTA and IOUTB. The complementary voltages appearing
at IOUTA and IOUTB (i.e., VOUTA and VOUTB) swing symmetrically
around ACOM and should be maintained with the specified
output compliance range of the AD9755. A differential resistor,
RDIFF, may be inserted into applications where the output of the
transformer is connected to the load, RLOAD, via a passive
reconstruction filter or cable. RDIFF is determined by the
transformer’s impedance ratio and provides the proper source
termination that results in a low VSWR.
相關PDF資料 |
PDF描述 |
|---|---|
| AD9762ARU | IC DAC 12BIT 125MSPS 28-TSSOP |
| AD9764AR | IC DAC 14BIT 125MSPS 28-SOIC |
| AD9779BSVZ | IC DAC 16BIT DUAL 1GSPS 100TQFP |
| AD9786BSVZRL | IC DAC 16BIT INTERPOL/SP 80TQFP |
| AD9788BSVZRL | IC DAC 16BIT 800MSPS 100TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9755-EB | 功能描述:BOARD EVAL FOR AD9755 RoHS:否 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:TxDAC+® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| AD976 | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit, 100 kSPS/200 kSPS BiCMOS A/D Converters |
| AD9760 | 制造商:AD 制造商全稱:Analog Devices 功能描述:10-Bit, 125 MSPS TxDAC D/A Converter |
| AD9760-50AR | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:10-Bit Digital-to-Analog Converter |
發布緊急采購，3分鐘左右您將得到回復。