參數資料
型號： AD9755ASTZRL
廠商： Analog Devices Inc
文件頁數： 7/28頁
文件大小： 0K
描述： IC DAC 14BIT 300MSPS 48-LQFP
產品培訓模塊： Data Converter Fundamentals
DAC Architectures
標準包裝： 2,000
系列： TxDAC+®
設置時間： 11ns
位數： 14
數據接口： 并聯
轉換器數目： 1
電壓電源： 模擬和數字
功率耗散（最大）： 165mW
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 48-LQFP
供應商設備封裝： 48-LQFP（7x7）
包裝： 帶卷 (TR)
輸出數目和類型： 2 電流，單極；2 電流，雙極
采樣率（每秒）： 300M
配用： AD9755-EB-ND - BOARD EVAL FOR AD9755
REV. B
AD9755
–15–
The AD9755 features a flexible differential clock input operating
from separate supplies (i.e., CLKVDD, CLKCOM) to achieve
optimum jitter performance. The two clock inputs, CLK+ and
CLK–, can be driven from a single-ended or differential clock
source. For single-ended operation, CLK+ should be driven by
a logic source while CLK– should be set to the threshold voltage
of the logic source. This can be done via a resistor divider/
capacitor network, as shown in Figure 15a. For differential opera-
tion, both CLK+ and CLK– should be biased to CLKVDD/2
via a resistor divider network, as shown in Figure 15b.
Because the output of the AD9755 can be updated at up to
300 MSPS, the quality of the clock and data input signals are
important in achieving the optimum performance. The drivers
of the digital data interface circuitry should be specified to
meet the minimum setup-and-hold times of the AD9755 as
well as its required min/max input logic level thresholds.
Digital signal paths should be kept short and run lengths matched
to avoid propagation delay mismatch. Inserting a low value
resistor network (i.e., 20
to 100 ) between the AD9755 digi-
tal inputs and driver outputs may be helpful in reducing any
overshooting and ringing at the digital inputs that contribute to
data feedthrough. For longer run lengths and high data update
rates, strip line techniques with proper termination resistors
should be considered to maintain “clean” digital inputs.
The external clock driver circuitry should provide the AD9755
with a low jitter clock input meeting the min/max logic levels
while providing fast edges. Fast clock edges help minimize any
jitter that manifests itself as phase noise on a reconstructed
waveform. Thus, the clock input should be driven by the fastest
logic family suitable for the application.
Note that the clock input could also be driven via a sine wave
that is centered around the digital threshold (i.e., DVDD/2) and
meets the min/max logic threshold. This typically results in a
slight degradation in the phase noise, which becomes more
noticeable at higher sampling rates and output frequencies. Also,
at higher sampling rates, the 20% tolerance of the digital logic
threshold should be considered since it affects the effective clock
duty cycle and, subsequently, cuts into the required data setup-
and-hold times.
RSERIES
0.1 F
VTHRESHOLD
CLK+
CLKVDD
CLK–
CLKCOM
AD9755
Figure 15a. Single-Ended Clock Interface
0.1 F
CLK+
CLKVDD
CLK–
CLKCOM
AD9755
0.1 F
Figure 15b. Differential Clock Interface
INPUT CLOCK AND DATA TIMING RELATIONSHIP
SNR in a DAC is dependent on the relationship between the
position of the clock edges and the point in time at which the
input data changes. The AD9755 is rising edge triggered, and so
exhibits SNR sensitivity when the data transition is close to this
edge. In general, the goal when applying the AD9755 is to make
the data transition close to the falling clock edge. This becomes
more important as the sample rate increases. Figure 16 shows
the relationship of SNR to clock placement with different sample
rates. Note that the setup-and-hold times implied in Figure 16
appear to violate the maximums stated in the Digital Specifica-
tions table. The variation in Figure 16 is due to the skew present
between data bits inherent in the digital data generator used to
perform these tests. Figure 16 is presented to show the effects of
violating setup-and-hold times, and to show the insensitivity of the
AD9755 to clock placement when data transitions fall outside of
the so-called “bad window.” The setup-and-hold times stated in
the Digital Specifications table were measured on a bit-by-bit basis,
therefore eliminating the skew present in the digital data generator.
At higher data rates, it becomes very important to account for the
skew in the input digital data when defining timing specifications.
TIME OF DATA TRANSITION RELATIVE TO PLACEMENT OF
CLK RISING EDGE (ns), fOUT = 10MHz, fDAC = 300MHz
80
40
0
3
0
–3
SNR
(dBc)
60
20
70
30
50
10
–2
–1
1
2
Figure 16. SNR vs. Time of Data Transition Relative to
Clock Rising Edge
POWER DISSIPATION
The power dissipation, PD, of the AD9755 is dependent on sev-
eral factors that include the power supply voltages (AVDD and
DVDD), the full-scale current output IOUTFS, the update rate
fCLOCK, and the reconstructed digital input waveform. The power
dissipation is directly proportional to the analog supply current,
IAVDD, and the digital supply current, IDVDD. IAVDD is directly
proportional to IOUTFS, as shown in Figure 17, and is insensitive
to fCLOCK. Conversely, IDVDD is dependent on both the digital
input waveform, fCLOCK, and digital supply DVDD. Figure 18
shows IDVDD as a function of the ratio (fOUT/fDAC) for various
update rates. In addition, Figure 19 shows the effect that the
speed of fDAC has on the PLLVDD current, given the PLL
divider ratio.
相關PDF資料
PDF描述
AD9762ARU IC DAC 12BIT 125MSPS 28-TSSOP
AD9764AR IC DAC 14BIT 125MSPS 28-SOIC
AD9779BSVZ IC DAC 16BIT DUAL 1GSPS 100TQFP
AD9786BSVZRL IC DAC 16BIT INTERPOL/SP 80TQFP
AD9788BSVZRL IC DAC 16BIT 800MSPS 100TQFP
相關代理商/技術參數
參數描述
AD9755-EB 功能描述:BOARD EVAL FOR AD9755 RoHS:否 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:TxDAC+® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581
AD976 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit, 100 kSPS/200 kSPS BiCMOS A/D Converters
AD9760 制造商:AD 制造商全稱:Analog Devices 功能描述:10-Bit, 125 MSPS TxDAC D/A Converter
AD9760-50AR 制造商:未知廠家 制造商全稱:未知廠家 功能描述:10-Bit Digital-to-Analog Converter
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*