- 您現在的位置：買賣IC網 > PDF目錄1893 > AD9755ASTZRL (Analog Devices Inc)IC DAC 14BIT 300MSPS 48-LQFP PDF資料下載
參數資料
| 型號： | AD9755ASTZRL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 14/28頁 |
| 文件大小： | 0K |
| 描述： | IC DAC 14BIT 300MSPS 48-LQFP |
| 產品培訓模塊： | Data Converter Fundamentals DAC Architectures |
| 標準包裝： | 2,000 |
| 系列： | TxDAC+® |
| 設置時間： | 11ns |
| 位數： | 14 |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 電壓電源： | 模擬和數字 |
| 功率耗散（最大）： | 165mW |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-LQFP |
| 供應商設備封裝： | 48-LQFP（7x7） |
| 包裝： | 帶卷 (TR) |
| 輸出數目和類型： | 2 電流，單極；2 電流，雙極 |
| 采樣率（每秒）： | 300M |
| 配用： | AD9755-EB-ND - BOARD EVAL FOR AD9755 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
REV. B
AD9755
–21–
Pseudo Zero Stuffing/IF Mode
The excellent dynamic range of the AD9755 allows its use in
applications where synthesis of multiple carriers is desired. In
addition, the AD9755 can be used in a pseudo zero-stuffing
mode, which improves dynamic range at IF frequencies. In this
mode, data from the two input channels is interleaved to the
DAC, which is running at twice the speed of either of the input
ports. However, the data at Port 2 is held constant at midscale.
The effect of this is shown in Figure 33. The IF signal is the
image, with respect to the input data rate, of the fundamental.
Normally, the sinx/x response of the DAC attenuates this image.
Zero stuffing improves the passband flatness so that the image
amplitude is closer to that of the fundamental signal. Zero stuffing
can be an especially useful technique in the synthesis of IF signals.
FREQUENCY (Normalized to Input Data Rate)
0
–30
2.0
0.5
0
EFFECT
OF
SINX/X
ROLL-OFF –20
–50
–10
–40
1.0
1.5
AMPLITUDE
OF IMAGE
WITHOUT
ZERO STUFFING
AMPLITUDE
OF IMAGE
USING
ZERO STUFFING
Figure 33. Effects of Pseudo Zero Stuffing on Spectrum
of AD9755
EVALUATION BOARD
The AD9755-EB is an evaluation board for the AD9755 TxDAC.
Careful attention to layout and circuit design, combined with
prototyping area, allows the user to easily and effectively evaluate
the AD9755 in different modes of operation.
Referring to Figures 34 and 35, the AD9755’s performance
can be evaluated differentially or single-ended using either a
transformer, or directly coupling the output. To evaluate the
output differentially using the transformer, it is recommended
that either the Mini-Circuits T1-1T (through-hole) or the
Coilcraft TTWB-1-B (SMT) be placed in the position of T1
on the evaluation board. To evaluate the output either single-
ended or direct-coupled, remove the transformer and bridge
either BL1 or BL2.
The digital data to the AD9755 comes from two ribbon cables that
interface to the 40-lead IDC connectors P1 and P2. Proper termi-
nation or voltage scaling can be accomplished by installing the
resistor pack networks RN1–RN12. RN1, R4, R7, and R10 are
22
DIP resistor packs and should be installed as they help reduce
the digital edge rates and therefore peak current on the inputs.
A single-ended clock can be applied via J3. By setting the SE/DIFF
labeled jumpers J2, J3, J4, and J6, the input clock can be directed
to the CLK+/CLK– inputs of the AD9755 in either a single-ended
or differential manner. If a differentially applied clock is desired,
a Mini-Circuits T1-1T transformer should be used in the position
of T2. Note that with a single-ended square wave clock input, T2
must be removed. A clock can also be applied via the ribbon cable
on Port 1 (P1), Pin 33. By inserting the EDGE jumper (JP1), this
clock will be applied to the CLK+ input of the AD9755. JP3
should be set in its SE position in this application to bias CLK–
to half the supply voltage.
The AD9755’s PLL clock multiplier can be enabled by inserting
JP7 in the IN position. As described in the Typical Performance
Characteristics and Functional Description section, with the
PLL enabled, a clock at half the output data rate should be
applied as described in the last paragraph. The PLL takes care
of the internal 2
× frequency multiplication and all internal timing
requirements. In this application, the PLLLOCK output indicates
when lock is achieved on the PLL. With the PLL enabled, the
DIV0 and DIV1 jumpers (JP8 and JP9) provide the PLL divider
ratio as described in Table I.
The PLL is disabled when JP7 is in the EX setting. In this mode,
a clock at the speed of the output data rate must be applied to the
clock inputs. Internally, the clock is divided by 2. For data
synchronization, a 1
× clock is provided on the PLLLOCK pin
in this application. Care should be taken to read the timing
requirements described earlier in the data sheet for optimum perfor-
mance. With the PLL disabled, the DIV0 and DIV1 jumpers
define the mode (interleaved, noninterleaved) as described in
Table II.
相關PDF資料 |
PDF描述 |
|---|---|
| AD9762ARU | IC DAC 12BIT 125MSPS 28-TSSOP |
| AD9764AR | IC DAC 14BIT 125MSPS 28-SOIC |
| AD9779BSVZ | IC DAC 16BIT DUAL 1GSPS 100TQFP |
| AD9786BSVZRL | IC DAC 16BIT INTERPOL/SP 80TQFP |
| AD9788BSVZRL | IC DAC 16BIT 800MSPS 100TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9755-EB | 功能描述:BOARD EVAL FOR AD9755 RoHS:否 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:TxDAC+® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| AD976 | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit, 100 kSPS/200 kSPS BiCMOS A/D Converters |
| AD9760 | 制造商:AD 制造商全稱:Analog Devices 功能描述:10-Bit, 125 MSPS TxDAC D/A Converter |
| AD9760-50AR | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:10-Bit Digital-to-Analog Converter |
發布緊急采購，3分鐘左右您將得到回復。