- 您現在的位置：買賣IC網 > PDF目錄165343 > AD9643BCPZ-210 (ANALOG DEVICES INC) 2-CH 14-BIT FLASH METHOD ADC, PARALLEL ACCESS, QCC64 PDF資料下載
參數資料
| 型號： | AD9643BCPZ-210 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | 2-CH 14-BIT FLASH METHOD ADC, PARALLEL ACCESS, QCC64 |
| 封裝： | 9 X 9 MM, ROHS COMPLIANT, MO-220VMMD-4, LFCSP-64 |
| 文件頁數： | 29/36頁 |
| 文件大?。?/td> | 1659K |
| 代理商： | AD9643BCPZ-210 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
AD9643
Rev. A | Page 35 of 36
APPLICATIONS INFORMATION
DESIGN GUIDELINES
Before starting system level design and layout of the AD9643,
it is recommended that the designer become familiar with these
guidelines, which discuss the special circuit connections and
layout requirements needed for certain pins.
Power and Ground Recommendations
When connecting power to the AD9643, it is recommended
that two separate 1.8 V supplies be used: one supply should be
used for analog (AVDD), and a separate supply should be used
for the digital outputs (DRVDD). The designer can employ
several different decoupling capacitors to cover both high and
low frequencies. These capacitors should be located close to the
point of entry at the PC board level and close to the pins of the
part with minimal trace length.
A single PCB ground plane should be sufficient when using the
AD9643. With proper decoupling and smart partitioning of the
PCB analog, digital, and clock sections, optimum performance
is easily achieved.
Exposed Paddle Thermal Heat Slug Recommendations
It is mandatory that the exposed paddle on the underside of the
ADC be connected to analog ground (AGND) to achieve the
best electrical and thermal performance. A continuous, exposed
(no solder mask) copper plane on the PCB should mate to the
AD9643 exposed paddle, Pin 0.
The copper plane should have several vias to achieve the lowest
possible resistive thermal path for heat dissipation to flow through
the bottom of the PCB. These vias should be filled or plugged with
nonconductive epoxy.
To maximize the coverage and adhesion between the ADC
and the PCB, a silkscreen should be overlaid to partition the
continuous plane on the PCB into several uniform sections.
This provides several tie points between the ADC and the PCB
during the reflow process. Using one continuous plane with no
partitions guarantees only one tie point between the ADC and
the PCB. See the evaluation board for a PCB layout example.
For detailed information about the packaging and PCB layout
of chip scale packages, refer to the AN-772 Application Note, A
Design and Manufacturing Guide for the Lead Frame Chip Scale
Package (LFCSP).
VCM
The VCM pin should be decoupled to ground with a 0.1 μF
capacitor, as shown in Figure 48. For optimal channel-to-channel
isolation, a 33 Ω resistor should be included between the AD9643
VCM pin and the Channel A analog input network connection,
as well as between the AD9643 VCM pin and the Channel B
analog input network connection.
SPI Port
The SPI port should not be active during periods when the full
dynamic performance of the converter is required. Because the
SCLK, CSB, and SDIO signals are typically asynchronous to the
ADC clock, noise from these signals can degrade converter
performance. If the on-board SPI bus is used for other devices,
it may be necessary to provide buffers between this bus and the
AD9643 to keep these signals from transitioning at the converter
input pins during critical sampling periods.
相關PDF資料 |
PDF描述 |
|---|---|
| AD9643BCPZ-250 | 2-CH 14-BIT FLASH METHOD ADC, PARALLEL ACCESS, QCC64 |
| AD9643BCPZRL7-210 | 2-CH 14-BIT FLASH METHOD ADC, PARALLEL ACCESS, QCC64 |
| AD9753ASTZRL | PARALLEL, WORD INPUT LOADING, 0.011 us SETTLING TIME, 12-BIT DAC, PQFP48 |
| ADA123AL7 | FIBER OPTIC ADD/DROP MUX/DEMUX, LC/UPC CONNECTOR |
| ADA123AB1 | FIBER OPTIC ADD/DROP MUX/DEMUX, FC/PC CONNECTOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9643BCPZ-250 | 功能描述:模數轉換器 - ADC 14 Bit 250Msps Dual ADC RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體: |
| AD9643BCPZRL7-170 | 功能描述:模數轉換器 - ADC 14 Bit 170Msps Dual ADC RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體: |
| AD9643BCPZRL7-210 | 功能描述:模數轉換器 - ADC 14 Bit 210Msps Dual ADC RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體: |
| AD9643BCPZRL7-250 | 功能描述:模數轉換器 - ADC 14 Bit 250Msps Dual ADC RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體: |
| AD9644-155KITZ | 功能描述:KIT EVAL FOR AD9644 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:* 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
發布緊急采購，3分鐘左右您將得到回復。