- 您現在的位置：買賣IC網 > PDF目錄1988 > AD9640ABCPZ-125 (Analog Devices Inc)IC ADC 14BIT 125MSPS 64LFCSP PDF資料下載
參數資料
| 型號： | AD9640ABCPZ-125 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 18/52頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 14BIT 125MSPS 64LFCSP |
| 設計資源： | Interfacing ADL5534 to AD9640 High Speed ADC (CN0049) |
| 標準包裝： | 1 |
| 位數： | 14 |
| 采樣率（每秒）： | 125M |
| 數據接口： | 串行，SPI? |
| 轉換器數目： | 2 |
| 功率耗散（最大）： | 846mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 64-LFCSP-VQ（9x9） |
| 包裝： | 托盤 |
| 輸入數目和類型： | 4 個單端，單極；2 個差分，單極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
AD9640
Rev. B | Page 25 of 52
THEORY OF OPERATION
The AD9640 dual ADC design can be used for diversity reception
of signals, where the ADCs are operating identically on the same
carrier but from two separate antennae. The ADCs can also be
operated with independent analog inputs. The user can sample
any fS/2 frequency segment from dc to 200 MHz using appropriate
low-pass or band-pass filtering at the ADC inputs with little loss
in ADC performance. Operation to 450 MHz analog input is
permitted but occurs at the expense of increased ADC distortion.
In nondiversity applications, the AD9640 can be used as a base-
band receiver, where one ADC is used for I input data and the
other is used for Q input data.
Synchronizaton capability is provided to allow synchronized
timing between multiple channels or multiple devices.
Programming and control of the AD9640 are accomplished
using a 3-bit SPI-compatible serial interface.
ADC ARCHITECTURE
The AD9640 architecture consists of a dual front-end sample-
and-hold amplifier (SHA), followed by a pipelined, switched
capacitor ADC. The quantized outputs from each stage are
combined into a final 14-bit result in the digital correction
logic. The pipelined architecture permits the first stage to
operate on a new input sample, and the remaining stages
operate on preceding samples. Sampling occurs on the rising
edge of the clock.
Each stage of the pipeline, excluding the last, consists of a low
resolution flash ADC connected to a switched capacitor digital-
to-analog converter (DAC) and an interstage residue amplifier
(MDAC). The residue amplifier magnifies the difference between
the reconstructed DAC output and the flash input for the next
stage in the pipeline. One bit of redundancy is used in each stage
to facilitate digital correction of flash errors. The last stage
simply consists of a flash ADC.
The input stage of each channel contains a differential SHA that
can be ac- or dc-coupled in differential or single-ended modes.
The output staging block aligns the data, carries out error correc-
tion, and passes the data to the output buffers. The output buffers
are powered from a separate supply, allowing adjustment of the
output voltage swing. During power-down, the output buffers go
into a high impedance state.
ANALOG INPUT CONSIDERATIONS
The analog input to the AD9640 is a differential switched
capacitor SHA that has been designed for optimum performance
while processing a differential input signal.
The clock signal alternatively switches the SHA between sample
mode and hold mode (see Figure 45). When the SHA is switched
into sample mode, the signal source must be capable of charging
the sample capacitors and settling within of a clock cycle.
A small resistor in series with each input can help reduce the
peak transient current required from the output stage of the
driving source. A shunt capacitor can be placed across the
inputs to provide dynamic charging currents. This passive
network creates a low-pass filter at the ADC input; therefore,
the precise values are dependent on the application.
In intermediate frequency (IF) undersampling applications,
any shunt capacitors should be reduced. In combination with
the driving source impedance, they limit the input bandwidth.
See the AN-742 Application Note, Frequency Domain Response
of Switched-Capacitor ADCs; the AN-827 Application Note, A
Resonant Approach to Interfacing Amplifiers to Switched-Capacitor
ADCs; and the Analog Dialogue article, “Transformer-Coupled
Front-End for Wideband A/D Converters” for more information
on this subject.
VIN+
VIN–
CPIN, PAR
CS
CH
H
S
06
54
7-
0
24
Figure 45. Switched-Capacitor SHA Input
For best dynamic performance, the source impedances driving
VIN+ and VIN should be matched.
An internal differential reference buffer creates positive and
negative reference voltages that define the input span of the ADC
core. The span of the ADC core is set by the buffer to 2 × VREF.
Input Common Mode
The analog inputs of the AD9640 are not internally dc biased.
In ac-coupled applications, the user must provide this bias
externally. Setting the device so that VCM = 0.55 × AVDD
is recommended for optimum performance, but the device
functions over a wider range with reasonable performance
(see Figure 44). An on-board common-mode voltage reference
is included in the design and is available from the CML pin.
Optimum performance is achieved when the common-mode
voltage of the analog input is set by the CML pin voltage
(typically 0.55 × AVDD). The CML pin must be decoupled to
ground by a 0.1 μF capacitor, as described in the Applications
Information section.
Differential Input Configurations
Optimum performance is achieved while driving the AD9640
in a differential input configuration. For baseband applications,
the AD8138 differential driver provides excellent performance
and a flexible interface to the ADC.
相關PDF資料 |
PDF描述 |
|---|---|
| AD9641BCPZ-80 | IC ADC 14BIT SRL 80MSPS 32LFCSP |
| AD9644BCPZ-80 | IC ADC 14BIT 80MSPS 3V 48LFCSP |
| AD9648BCPZRL7-125 | IC ADC 14BIT 125MSPS 64LFCSP |
| AD9649BCPZRL7-80 | IC ADC 14BIT 80MSPS 32LFCSP |
| AD9653BCPZRL7-125 | IC ADC 16BIT 125MSPS SRL 48LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9640ABCPZ-150 | 功能描述:模數轉換器 - ADC 14Bit 150Msps Dual 1.8V PB Free ADC RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體: |
| AD9640ABCPZ-80 | 功能描述:IC ADC 14BIT 80MSPS 64LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD9640ABCPZRL7-105 | 功能描述:模數轉換器 - ADC 14Bit 105Msps Dual 1.8V PB Free ADC RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體: |
| AD9640ABCPZRL7-125 | 功能描述:14 Bit Analog to Digital Converter 2 Input 2 Pipelined 64-LFCSP-VQ (9x9) 制造商:analog devices inc. 系列:- 包裝:帶卷（TR） 零件狀態:在售 位數:14 采樣率（每秒）:125M 輸入數:2 輸入類型:差分，單端 數據接口:并聯 配置:S/H-ADC 無線電 - S/H:ADC:1:1 A/D 轉換器數:2 架構:管線 參考類型:外部， 內部 電壓 - 電源，模擬:1.7 V ~ 1.9 V 電壓 - 電源，數字:1.7 V ~ 1.9 V 特性:同步采樣 工作溫度:-40°C ~ 85°C 封裝/外殼:64-VFQFN 裸露焊盤，CSP 供應商器件封裝:64-LFCSP-VQ（9x9） 標準包裝:750 |
| AD9640ABCPZRL7-80 | 制造商:AD 制造商全稱:Analog Devices 功能描述:14-Bit, 80/105/125/150 MSPS, 1.8 V Dual Analog-to-Digital Converter |
發布緊急采購，3分鐘左右您將得到回復。