- 您現在的位置：買賣IC網 > PDF目錄16533 > AD9517-4A/PCBZ (Analog Devices Inc)BOARD EVALUATION FOR AD9517-4A PDF資料下載
參數資料
| 型號： | AD9517-4A/PCBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 74/80頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVALUATION FOR AD9517-4A |
| 設計資源： | High Performance, Dual Channel IF Sampling Receiver (CN0140) AD9517 Eval Brd Schematics AD9517 Gerber Files AD9517-4 BOM |
| 標準包裝： | 1 |
| 主要目的： | 計時，時鐘發生器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | AD9517-4A |
| 主要屬性： | 2 輸入，12 輸出，1.6GHz VCO |
| 次要屬性： | CMOS，LVPECL 和 LVDS 兼容 |
| 已供物品： | 板 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁當前第74頁第75頁第76頁第77頁第78頁第79頁第80頁
AD9517-4
Data Sheet
Rev. E | Page 76 of 80
APPLICATIONS INFORMATION
FREQUENCY PLANNING USING THE AD9517
The AD9517 is a highly flexible PLL. When choosing the PLL
settings and version of the AD9517, keep in mind the following
guidelines.
The AD9517 has the following four frequency dividers: the
reference (or R) divider, the feedback (or N) divider, the VCO
divider, and the channel divider. When trying to achieve a
particularly difficult frequency divide ratio requiring a large
amount of frequency division, some of the frequency division
can be done by either the VCO divider or the channel divider,
thus allowing a higher phase detector frequency and more
flexibility in choosing the loop bandwidth.
Within the AD9517 family, lower VCO frequencies generally
result in slightly lower jitter. The difference in integrated jitter
(from 12 kHz to 20 MHz offset) for the same output frequency is
usually less than 150 fs over the entire VCO frequency range
(1.45 GHz to 2.95 GHz) of the AD9517 family. If the desired
frequency plan can be achieved with a version of the AD9517
that has a lower VCO frequency, choosing the lower frequency
part results in the lowest phase noise and the lowest jitter.
However, choosing a higher VCO frequency may result in more
flexibility in frequency planning.
Choosing a nominal charge pump current in the middle of the
allowable range as a starting point allows the designer to increase or
decrease the charge pump current, and thus allows the designer
to fine-tune the PLL loop bandwidth in either direction.
ADIsimCLK is a powerful PLL modeling tool that can be
downloaded from www.analog.com. It is a very accurate tool for
determining the optimal loop filter for a given application.
USING THE AD9517 OUTPUTS FOR ADC CLOCK
APPLICATIONS
Any high speed ADC is extremely sensitive to the quality of its
sampling clock. An ADC can be thought of as a sampling mixer,
and any noise, distortion, or timing jitter on the clock is combined
with the desired signal at the analog-to-digital output. Clock
integrity requirements scale with the analog input frequency
and resolution, with higher analog input frequency applications
at ≥14-bit resolution being the most stringent. The theoretical
SNR of an ADC is limited by the ADC resolution and the jitter
on the sampling clock. Considering an ideal ADC of infinite
resolution where the step size and quantization error can be
ignored, the available SNR can be expressed approximately by
π
×
=
J
At
f
SNR
2
1
log
20
(dB)
where:
fA is the highest analog frequency being digitized.
tJ is the rms jitter on the sampling clock.
Figure 70 shows the required sampling clock jitter as a function
of the analog frequency and effective number of bits (ENOB).
fA (MHz)
S
NR
(
d
B)
E
NO
B
10
1k
100
30
40
50
60
70
80
90
100
110
6
8
10
12
14
16
18
t
J = 100
f
S
200
f
S
400
f
S
1ps
2ps
10p
s
SNR = 20log
1
2πfAtJ
06428-
044
Figure 70. SNR and ENOB vs. Analog Input Frequency
See the AN-756 Application Note, Sampled Systems and the Effects
of Clock Phase Noise and Jitter; and the AN-501 Application Note,
Aperture Uncertainty and ADC System Performance, at
Many high performance ADCs feature differential clock inputs
to simplify the task of providing the required low jitter clock on
a noisy PCB. (Distributing a single-ended clock on a noisy PCB
may result in coupled noise on the sample clock. Differential
distribution has inherent common-mode rejection that can provide
superior clock performance in a noisy environment.) The AD9517
features both LVPECL and LVDS outputs that provide differential
clock outputs, which enable clock solutions that maximize
converter SNR performance. The input requirements of the ADC
(differential or single-ended, logic level, termination) should be
considered when selecting the best clocking/converter solution.
相關PDF資料 |
PDF描述 |
|---|---|
| FCBP110LD1L20 | CABLE 10.5GBPS 20M LASERWIRE |
| VE-JTZ-EZ-S | CONVERTER MOD DC/DC 2V 10W |
| AD9518-0A/PCBZ | BOARD EVALUATION FOR AD9518-0A |
| FCBP110LD1L10S | KIT 10M LASERWIRE SFP+ |
| VE-JTX-EZ-S | CONVERTER MOD DC/DC 5.2V 25W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9517-4BCPZ | 制造商:Analog Devices 功能描述: 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述:IC CLOCK GENERATOR 1.8GHZ LFCSP-48 制造商:Analog Devices 功能描述:IC, CLOCK GENERATOR, 1.8GHZ, LFCSP-48, Clock IC Type:Clock Generator, Frequency: |
| AD9517-4BCPZ-REEL7 | 制造商:Analog Devices 功能描述: |
| AD9518-0 | 制造商:AD 制造商全稱:Analog Devices 功能描述:6-Output Clock Generator |
| AD9518-0/PCBZ | 制造商:Analog Devices 功能描述:Evaluation Kit For 6-Output Clock Generator With Integrated 2.8 GHZ VCO |
| AD9518-0A/PCBZ | 功能描述:BOARD EVALUATION FOR AD9518-0A RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081 |
發布緊急采購，3分鐘左右您將得到回復。