- 您現在的位置：買賣IC網 > PDF目錄1986 > AD9230BCPZ11-200 (Analog Devices Inc)IC ADC 11-BIT 200MSPS 56-LFCSP PDF資料下載
參數資料
| 型號： | AD9230BCPZ11-200 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 8/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 11-BIT 200MSPS 56-LFCSP |
| 標準包裝： | 1 |
| 位數： | 11 |
| 采樣率（每秒）： | 200M |
| 數據接口： | 串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 373mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 56-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 56-LFCSP-VQ（8x8） |
| 包裝： | 托盤 |
| 輸入數目和類型： | 1 個差分，單極 |
| 配用： | AD923011-200EBZ-ND - BOARD EVAL FOR AD9230 200MSPS |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
AD9230-11
Rev. 0 | Page 16 of 28
THEORY OF OPERATION
The AD9230-11 architecture consists of a front-end sample-
and-hold amplifier (SHA) followed by a pipelined switched
capacitor ADC. The quantized outputs from each stage are
combined into a final 11-bit result in the digital correction
logic. The pipelined architecture permits the first stage to
operate on a new input sample, while the remaining stages operate
on preceding samples. Sampling occurs on the rising edge of the
clock.
Each stage of the pipeline, excluding the last, consists of a low
resolution flash ADC connected to a switched capacitor DAC
and interstage residue amplifier (MDAC). The residue amplifier
magnifies the difference between the reconstructed DAC output
and the flash input for the next stage in the pipeline. One bit of
redundancy is used in each stage to facilitate digital correction
of flash errors. The last stage simply consists of a flash ADC.
The input stage contains a buffered differential SHA that can
be ac- or dc-coupled. The output staging block aligns the data,
carries out the error correction, and passes the data to the out-
put buffers. The output buffers are powered from a separate
supply, allowing adjustment of the output voltage swing. During
power-down, the output buffers go into a high impedance state.
ANALOG INPUT AND VOLTAGE REFERENCE
The analog input to the AD9230-11 is a differential buffer. For
best dynamic performance, the source impedances driving
VIN+ and VIN should be matched such that common-mode
settling errors are symmetrical. The analog input is optimized
to provide superior wideband performance and requires that
the analog inputs be driven differentially. SNR and SINAD
performance degrades significantly if the analog input is driven
with a single-ended signal.
A wideband transformer, such as Mini-Circuits ADT1-1WT, can
provide the differential analog inputs for applications that require a
single-ended-to-differential conversion. Both analog inputs are self-
biased by an on-chip resistor divider to a nominal 1.4 V. An
internal differential voltage reference creates positive and negative
reference voltages that define the 1.25 V p-p fixed span of the ADC
core. This internal voltage reference can be adjusted by means of
SPI control. See the Configuration Using the SPI section.
Differential Input Configurations
Optimum performance is achieved while driving the AD9230-11
in a differential input configuration. For baseband applications,
the AD8138 differential driver provides excellent performance
and a flexible interface to the ADC. The output common-mode
voltage of the AD8138 is easily set to AVDD/2 + 0.5 V, and the
driver can be configured in a Sallen-Key filter topology to
provide band limiting of the input signal.
VIN+
VIN–
AVDD
CML
AD8138
523
499
33
49.9
1V p-p
0.1F
20pF
AD9230-11
0
71
01
-0
14
Figure 21. Differential Input Configuration Using the AD8138
At input frequencies in the second Nyquist zone and above, the
performance of most amplifiers may not be adequate to achieve the
true performance of the AD9230-11. This is especially true in IF
undersampling applications where frequencies in the 70 MHz to
100 MHz range are being sampled. For these applications, differen-
tial transformer coupling is the recommended input configuration.
The signal characteristics must be considered when selecting a
transformer. Most RF transformers saturate at frequencies below a
few megahertz and excessive signal power can also cause core
saturation, leading to distortion. In any configuration, the value of
the shunt capacitor, C, is dependent on the input frequency and
may need to be reduced or removed.
VIN+
VIN–
15
50
1.25V p-p
0.1F
2pF
AD9230-11
07
10
1-
0
15
Figure 22. Differential Transformer—Coupled Configuration
As an alternative to using a transformer-coupled input at frequen-
cies in the second Nyquist zone, the AD8352 differential driver can
be used (see Figure 23).
AD9230-11
AD8352
0
R
0
CD
RD
RG
0.1F
VIN+
VIN– CML
C
0.1F
16
1
2
3
4
5
11
R
0.1F
10
8, 13
14
VCC
200
ANALOG INPUT
071
01-
01
6
Figure 23. Differential Input Configuration Using the AD8352
相關PDF資料 |
PDF描述 |
|---|---|
| AD9231BCPZ-80 | IC ADC 12BIT 80MSPS 64LFCSP |
| AD9233BCPZRL7-125 | IC ADC 12BIT 125MSPS 48-LFCSP |
| AD9235BRURL7-40 | IC ADC 12BIT SGL 40MSPS 28TSSOP |
| AD9236BRUZRL7-80 | IC ADC 12BIT 80MSPS 28TSSOP |
| AD9237BCPZ-20 | IC ADC 12BIT SGL 20MSPS 32LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9230BCPZ-170 | 功能描述:IC ADC 12BIT 170MSPS 56-LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD9230BCPZ-210 | 功能描述:模數轉換器 - ADC IC 12B 210Msps 1.8V RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體: |
| AD9230BCPZ-250 | 制造商:Analog Devices 功能描述:ADC Single Pipelined 250Msps 12-bit Parallel/LVDS 56-Pin LFCSP EP Tray 制造商:Analog Devices 功能描述:ADC SGL PIPELINED 250MSPS 12-BIT PARALLEL 56LFCSP EP - Trays 制造商:Analog Devices 功能描述:IC ADC 12BIT 250MSPS LFCSP-56 制造商:Analog Devices Inc. 功能描述:Analog to Digital Converters - ADC 12-Bit 250 Msps ADC 制造商:Analog Devices 功能描述:IC, ADC, 12BIT, 250MSPS, LFCSP-56; Resolution (Bits):12bit; Sampling Rate:250MSPS; Supply Voltage Type:Single; Supply Voltage Min:1.7V; Supply Voltage Max:1.9V; Supply Current:181mA; Digital IC Case Style:CSP; No. of Pins:56 ;RoHS Compliant: Yes 制造商:Analog Devices 功能描述:CONVERTER - ADC |
| AD9230BCPZRL7-170 | 功能描述:模數轉換器 - ADC IC 12B 170Msps 1.8V RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體: |
| AD9230XCPZ-170 | 制造商:Analog Devices 功能描述:12-BIT, 170/210/250 MSPS 1.8 V A/D CONVERTER - Trays |
發布緊急采購，3分鐘左右您將得到回復。