- 您現在的位置：買賣IC網 > PDF目錄2062 > AD8317ACPZ-R7 (Analog Devices Inc)IC AMP LOG DETECT 8GHZ 8-LFCSP PDF資料下載
參數資料
| 型號： | AD8317ACPZ-R7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 3/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP LOG DETECT 8GHZ 8-LFCSP |
| 產品培訓模塊： | Choosing and Using RF Detectors |
| 標準包裝： | 1 |
| 類型： | 對數放大器 |
| 應用： | 接收器信號強度指示（RSSI） |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-VFDFN 裸露焊盤 |
| 供應商設備封裝： | 8-LFCSP-VD（3x2） |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 550 (CN2011-ZH PDF) |
| 其它名稱： | AD8317ACPZ-R7DKR |
AD8317
Rev. B | Page 11 of 20
USING THE AD8317
BASIC CONNECTIONS
The AD8317 is specified for operation up to 10 GHz; as a result,
low impedance supply pins with adequate isolation between
functions are essential. A power supply voltage of between 3.0 V
and 5.5 V should be applied to VPOS. Power supply decoupling
capacitors of 100 pF and 0.1 μF should be connected close to
this power supply pin.
AD8317
1
2
3
4
8
7
6
5
SIGNAL
INPUT
VOUT
C2
C1
C5
C4
47nF
100pF
VS (3.0V TO 5.5V)
INHI
INLO
VPOS
TADJ
VOUT
COMM
CLPF
VSET
05
54
1-
02
2
0.1F
R2
0
R1
52.3
R4
0
1
1SEE THE TEMPERATURE COMPENSATION OF OUTPUT VOLTAGE SECTION.
2SEE THE OUTPUT FILTERING SECTION.
2
Figure 22. Basic Connections
The paddle of the LFCSP package is internally connected to
COMM. For optimum thermal and electrical performance, the
paddle should be soldered to a low impedance ground plane.
INPUT SIGNAL COUPLING
The RF input (INHI) is single-ended and must be ac-coupled.
INLO (input common) should be ac-coupled to ground.
Suggested coupling capacitors are 47 nF ceramic 0402-style
capacitors for input frequencies of 1 MHz to 10 GHz. The
coupling capacitors should be mounted close to the INHI and
INLO pins. The coupling capacitor values can be increased to
lower the high-pass cutoff frequency of the input stage. The
high-pass corner is set by the input coupling capacitors and the
internal 10 pF high-pass capacitor. The dc voltage on INHI and
INLO is approximately one diode voltage drop below VPOS.
05
54
1-
02
3
VPOS
2k
A = 9dB
18.7k
CURRENT
gm
STAGE
INLO
INHI
OFFSET
COMP
5pF
FIRST
GAIN
STAGE
Figure 23. Input Interface
While the input can be reactively matched, in general, this is not
necessary. An external 52.3 Ω shunt resistor (connected on the
signal side of the input coupling capacitors, as shown in
Figure 22) combines with the relatively high input impedance to
give an adequate broadband 50 Ω match.
The coupling time constant, 50 × CC/2, forms a high-pass
corner with a 3 dB attenuation at fHP = 1/(2π × 50 × CC ), where
C1 = C2 = CC. Using the typical value of 47 nF, this high-pass
corner is ~68 kHz. In high frequency applications, fHP should be
as large as possible to minimize the coupling of unwanted low
frequency signals. In low frequency applications, a simple RC
network forming a low-pass filter should be added at the input
for similar reasons. This low-pass filter network should generally
be placed at the generator side of the coupling capacitors, thereby
lowering the required capacitance value for a given high-pass
corner frequency.
OUTPUT INTERFACE
The VOUT pin is driven by a PNP output stage. An internal
10 Ω resistor is placed in series with the output and the VOUT
pin. The rise time of the output is limited mainly by the slew
on CLPF. The fall time is an RC-limited slew given by the load
capacitance and the pull-down resistance at VOUT. There is an
internal pull-down resistor of 1.6 kΩ. A resistive load at VOUT
is placed in parallel with the internal pull-down resistor to
provide additional discharge current.
05
541
-02
4
+
0.8V
1200
400
–
10
VOUT
VPOS
CLPF
COMM
Figure 24. Output Interface
To reduce the fall time, VOUT should be loaded with a resistive
load of <1.6 kΩ. For example, with an external load of 150 Ω,
the AD8317 fall time is <7 ns.
SETPOINT INTERFACE
The VSET input drives the high impedance (40 kΩ) input of an
internal op amp. The VSET voltage appears across the internal
1.5 kΩ resistor to generate ISET. When a portion of VOUT is
applied to VSET, the feedback loop forces
ID × log10(VIN/VINTERCEPT) = ISET
(2)
If VSET = VOUT/2x, then ISET = VOUT/(2x × 1.5 kΩ).
The result is
VOUT = (ID × 1.5 kΩ × 2x) × log10(VIN/VINTERCEPT)
05
54
1-
0
25
1.5k
ISET
COMM
VSET
VSET
COMM
20k
Figure 25. VSET Interface
相關PDF資料 |
PDF描述 |
|---|---|
| AD8321ARZ | IC LINE DRIVER CATV 3.3V 20SOIC |
| AD8322ARUZ-REEL | IC LN DVR CATV COARS-STP 28TSSOP |
| AD8324JRQZ-REEL | IC LINE DRIVER CBL 3.3V 20QSOP |
| AD8325ARUZ-REEL | IC LN DVR CATV FINE-STEP 28TSSOP |
| AD8326AREZ | IC LINE DVR CATV PROG 28TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8317ACPZ-R7 | 制造商:Analog Devices 功能描述:IC LOGARITHMIC AMPLIFIER 20NS LFCSP-8 |
| AD8317ACPZ-WP | 制造商:Analog Devices 功能描述: |
| AD8317-EVAL | 制造商:AD 制造商全稱:Analog Devices 功能描述:1 MHz to 10 GHz, 50 dB Log Detector/Controller |
| AD8317-EVALZ | 制造商:Analog Devices 功能描述:EVAL KIT FOR 1 MHZ TO 10 GHZ, 50 DB LOG DETECTOR/CNTRLR - Bulk 制造商:Analog Devices 功能描述:EVAL BOARD, AD8317 LOG DETECTOR/CNTRL, Silicon Manufacturer:Analog Devices, Silicon Core Number:AD8317, Kit Application Type:RF / IF, Kit Contents:Eval Board AD8317, Features:(Not Applicable) |
| AD8318 | 制造商:AD 制造商全稱:Analog Devices 功能描述:1 MHz to 8 GHz, 70 dB Logarithmic Detector/Controller |
發布緊急采購，3分鐘左右您將得到回復。