- 您現在的位置：買賣IC網 > PDF目錄1893 > AD8303ARZ-REEL (Analog Devices Inc)IC DAC 12BIT SERIAL 14SOIC PDF資料下載
參數資料
| 型號： | AD8303ARZ-REEL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 16/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAC 12BIT SERIAL 14SOIC |
| 產品培訓模塊： | Data Converter Fundamentals DAC Architectures |
| 產品變化通告： | AD8303 Obsolescence 15/Apr/2011 |
| 標準包裝： | 1 |
| 設置時間： | 14µs |
| 位數： | 12 |
| 數據接口： | 串行，SPI? |
| 轉換器數目： | 2 |
| 電壓電源： | 單電源 |
| 功率耗散（最大）： | 9.6mW |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 14-SOICN |
| 包裝： | 標準包裝 |
| 輸出數目和類型： | * |
| 采樣率（每秒）： | * |
| 其它名稱： | AD8303ARZ-REELDKR |
AD8303
REV. 0
–9–
POWER SUPPLY
The very low power consumption of the AD8303 is a direct
result of a circuit design optimizing the use of a CBCMOS
process. By using the low power characteristics of CMOS for
the logic, and the low noise, tight matching of the complementary
bipolar transistors, excellent analog accuracy is achieved.
One advantage of the rail-to-rail output amplifiers used in the
AD8303 is the wide range of usable supply voltage. The part is
fully specified and tested for operation from +2.7 V to +5.5 V.
If reduced linearity and source current capability near full scale
can be tolerated, operation of the AD8303 is possible down to
+2.7 V.
POWER SUPPLY BYPASSING AND GROUNDING
Precision analog products, such as the AD8303, require a well
filtered power source. Since the AD8303 operates from a single
+3 V to +5 V supply, it seems convenient to simply tap into the
digital logic power supply. Unfortunately, the logic supply is
often a switch-mode design, which generates noise in the
20 kHz to 1 MHz range. In addition, fast logic gates can
generate glitches hundred of millivolts in amplitude due to
wiring resistances and inductances. The power supply noise
generated thereby means that special care must be taken to
insure that the inherent precision of the DAC is maintained.
Good engineering judgment should be exercised when addressing
the power supply grounding and bypassing of the AD8303.
The AD8303 should be powered directly from the system power
supply. This arrangement, shown in Figure 24, employs an LC
filter and separate power and ground connections to isolate the
analog section from the logic switching transients. Analog and
digital ground pins of the AD8303 should be connected
together directly at the IC package.
100F
ELECT.
10-22F
TANT.
0.1F
CER.
TTL/CMOS
LOGIC
CIRCUITS
+5V
POWER SUPPLY
+5V
RETURN
FERRITE BEAD:
2 TURNS, FAIR-RITE
#2677006301
Figure 24. Use Separate Traces to Reduce Power Supply
Noise
Whether or not a separate power supply trace is available,
however, generous supply bypassing will reduce supply-line
induced errors. Local supply bypassing consisting of a 10
F
tantalum electrolytic in parallel with a 0.1
F ceramic capacitor
is recommended in all applications (Figure 25).
SDI
CLK
CS
LDA
LDB
RS
MSB
SHDN
AD8303
7
6
5
8
10
9
11
12
13
2
14
4
1
TO ANALOG GROUND
VOUTA
VOUTB
0.1F
10F
+2.7V TO +5.5V
AGND
DGND
VDD
Figure 25. Recommended Supply Bypassing for the
AD8303
INPUT LOGIC LEVELS
All digital inputs are protected with a Zener-type ESD protection
structure (Figure 26) that allows logic input voltages to exceed
the VDD supply voltage. This feature can be useful if the user is
driving one or more of the digital inputs with a 5 V CMOS logic
input voltage level while operating the AD8303 on a +3 V power
supply. If this mode of interface is used, make sure that the VOL
of the 5 V CMOS meets the VIL input requirement of the
AD8303 operating at 3 V. See Figure 6 for a graph for digital
logic input threshold versus operating VDD supply voltage.
VDD
LOGIC
IN
GND
Figure 26. Equivalent Digital Input ESD Protection
For power consumption-sensitive applications, it is important to
note that the internal power consumption of the AD8303 is
strongly dependent on the actual logic input voltage levels
present in the SDI, CLK, CS, LDA, LDB, SHDN, RS and
MSB pins. Since these inputs are standard CMOS logic
structures, they contribute static power dissipation which
depends on the actual driving logic VOH and VOL voltage levels.
Consequently, using CMOS logic versus TTL will provide
minimal dissipation in the static state.
相關PDF資料 |
PDF描述 |
|---|---|
| AD8391AR-REEL7 | IC XDSL LINE DVR W/PWR DN 8-SOIC |
| AD8392AAREZ | IC ADSL/ADSL2 LINE DRVR 28-TSSOP |
| AD8394AREZ-R7 | IC OPAMP ADSL/ADSL2 DL 20TSSOP |
| AD8396ACPZ-RL | IC LINE DRVR ADSL/ADSL2 16LFCSP |
| AD8398ACPZ-R7 | IC LINE DRVR DUAL VDSL 16-LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8303JRU | 制造商:Analog Devices 功能描述:DAC 2-CH R-2R 12-bit 14-Pin TSSOP 制造商:Rochester Electronics LLC 功能描述:IC,DUAL 12BIT,+3V,COMPLETE DAC - Bulk |
| AD8303JRU-REEL | 制造商:Analog Devices 功能描述:DAC 2-CH R-2R 12-bit 14-Pin TSSOP T/R |
| AD8303JRUZ | 制造商:Analog Devices 功能描述:DAC 2-CH R-2R 12-bit 14-Pin TSSOP |
| AD8304 | 制造商:AD 制造商全稱:Analog Devices 功能描述:160 dB Range (100 pA -10 mA) Logarithmic Converter |
| AD8304ARU | 功能描述:IC LOGARITHM CONV 160DB 14-TSSOP RoHS:否 類別:集成電路 (IC) >> 線性 - 放大器 - 專用 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:可變增益放大器 應用:CATV 安裝類型:表面貼裝 封裝/外殼:20-WQFN 裸露焊盤 供應商設備封裝:20-TQFN-EP（5x5） 包裝:托盤 |
發布緊急采購，3分鐘左右您將得到回復。
