參數資料
型號： AD7944BCPZ-RL7
廠商： Analog Devices Inc
文件頁數： 8/28頁
文件大?。?/td> 0K
描述： IC ADC 14B 2.5MSPS PULSR 20LFCSP
標準包裝： 1,500
系列： PulSAR®
位數： 14
采樣率（每秒）： 2.5M
數據接口： DSP，MICROWIRE?，QSPI?，串行，SPI?
轉換器數目： 1
功率耗散（最大）： 33mW
電壓電源： 模擬和數字
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 20-VFQFN 裸露焊盤，CSP
供應商設備封裝： 20-LFCSP-VQ
包裝： 帶卷 (TR)
輸入數目和類型： 1 個偽差分，單極
AD7944
Rev. A | Page 16 of 28
VOLTAGE REFERENCE INPUT
The AD7944 allows the choice of a very low temperature drift
internal voltage reference, an external reference, or an external
buffered reference.
The internal reference of the AD7944 provides excellent
performance and can be used in almost all applications.
Internal Reference, REF = 4.096 V (PDREF Low)
To use the internal reference, the PDREF input must be low.
This enables the on-chip band gap reference and buffer, result-
ing in a 4.096 V reference on the REF pin (1.2 V on REFIN).
The internal reference is temperature compensated to
4.096 V ± 15 mV. The reference is trimmed to provide
a typical drift of 10 ppm/°C.
The output resistance of REFIN is 6 k when the internal
reference is enabled. It is necessary to decouple this pin with a
ceramic capacitor of at least 100 nF. The output resistance of
REFIN and the decoupling capacitor form an RC filter, which
helps to reduce noise.
Because the output impedance of REFIN is typically 6 k,
relative humidity (among other industrial contaminants) can
directly affect the drift characteristics of the reference. A guard
ring is typically used to reduce the effects of drift under such
circumstances. However, the fine pitch of the AD7944 makes
this difficult to implement. One solution, in these industrial
and other types of applications, is to use a conformal coating,
such as Dow Corning 1-2577 or HumiSeal 1B73.
External 1.2 V Reference and Internal Buffer (PDREF High)
To use an external reference along with the internal buffer, PDREF
must be high. This powers down the internal reference and allows
the 1.2 V reference to be applied to REFIN, producing 4.096 V
(typically) on the REF pin.
External Reference (PDREF High, REFIN Low)
To apply an external reference voltage directly to the REF pin, tie
PDREF high and tie REFIN low. BVDD should also be driven to
the same potential as REF. For example, if REF = 2.5 V, BVDD
should be tied to 2.5 V.
The advantages of directly using an external voltage reference
are as follows:
SNR and dynamic range improvement (about 1.7 dB)
resulting from the use of a larger reference voltage (5 V)
instead of a typical 4.096 V reference when the internal
reference is used. This is calculated by
=
0
.
5
096
.
4
log
20
SNR
Power savings when the internal reference is powered
down (PDREF high).
Reference Decoupling
The AD7944 voltage reference input, REF, has a dynamic input
impedance that requires careful decoupling between the REF
and REFGND pins. The Layout section describes how this can
be done.
When using an external reference, a very low impedance source
(for example, a reference buffer using the AD8031 or the AD8605)
and a 10 F (X5R, 0805 size) ceramic chip capacitor are appro-
priate for optimum performance.
If an unbuffered reference voltage is used, the decoupling value
depends on the reference used. For example, a 22 F (X5R,
1206 size) ceramic chip capacitor is appropriate for optimum
performance using a low temperature drift ADR43x reference.
If desired, a reference decoupling capacitor with a value as small
as 2.2 F can be used with minimal impact on performance,
especially DNL.
In any case, there is no need for an additional, lower value
ceramic decoupling capacitor (for example, 100 nF) between
the REF and REFGND pins.
POWER SUPPLY
The AD7944 has four power supply pins: an analog supply
(AVDD), a buffer supply (BVDD), a digital supply (DVDD), and
a digital input/output interface supply (VIO). VIO allows a direct
interface to any logic from 1.8 V to 2.7 V. To reduce the number
of supplies needed, the VIO, DVDD, and AVDD pins can be
tied together. The power supplies do not need to be started in a
particular sequence. In addition, the AD7944 is very insensitive
to power supply variations over a wide frequency range.
In normal mode, the AD7944 powers down automatically at
the end of each conversion phase and, therefore, the power
scales linearly with the sampling rate. This makes the part ideal
for low sampling rates (even of a few SPS) and battery-powered
applications.
10
1
0.1
0.01
0.1
1
O
P
E
RAT
ING
CURRE
NT
(
mA)
SAMPLING RATE (MSPS)
IBVDD
IAVDD
IDVDD
IVIO
IVREF
04658-
121
Figure 25. Operating Current vs. Sampling Rate in Normal Mode
相關PDF資料
PDF描述
SP3243ECT-L/TR IC TXRX RS232 INTELLIGNT 28WSOIC
AD7658YSTZ-1-RL IC ADC 12BIT 6CH 250KSPS 64LQFP
AD7658YSTZ-REEL IC ADC 12BIT 6CH 250KSPS 64LQFP
SP3243EBCY-L/TR IC TXRX RS232 INTELLIGNT 28TSSOP
MS27499E20B16PA CONN RCPT 16POS BOX MNT W/PINS
相關代理商/技術參數
參數描述
AD7945 制造商:AD 制造商全稱:Analog Devices 功能描述:+3.3 V/+5 V Multiplying 12-Bit DACs
AD7945AN-B 功能描述:IC DAC 12BIT MULT PARALL 20-DIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:2,400 系列:- 設置時間:- 位數:18 數據接口:串行 轉換器數目:3 電壓電源:模擬和數字 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:36-TFBGA 供應商設備封裝:36-TFBGA 包裝:帶卷 (TR) 輸出數目和類型:* 采樣率（每秒）:*
AD7945ANZ-B 功能描述:IC DAC 12BIT MULT PARALL 20DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:47 系列:- 設置時間:2µs 位數:14 數據接口:并聯 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:55µW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:28-SSOP 包裝:管件 輸出數目和類型:1 電流，單極；1 電流，雙極 采樣率（每秒）:*
AD7945ARS-B 功能描述:IC DAC 12BIT MULT PARALL 20-SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:47 系列:- 設置時間:2µs 位數:14 數據接口:并聯 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:55µW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:28-SSOP 包裝:管件 輸出數目和類型:1 電流，單極；1 電流，雙極 采樣率（每秒）:*
AD7945ARS-BREEL 功能描述:IC DAC 12BIT MULT PARALL 20-SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:LTC263x 12-, 10-, and 8-Bit VOUT DAC Family 特色產品:LTC2636 - Octal 12-/10-/8-Bit SPI VOUT DACs with 10ppm/°C Reference 標準包裝:91 系列:- 設置時間:4µs 位數:10 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:8 電壓電源:單電源 功率耗散（最大）:2.7mW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-DFN-EP（4x3） 包裝:管件 輸出數目和類型:8 電壓，單極 采樣率（每秒）:*
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*