- 您現在的位置：買賣IC網 > PDF目錄10252 > AD7792BRU (Analog Devices Inc)IC ADC 16BIT 3CH LP 16-TSSOP PDF資料下載
參數資料
| 型號： | AD7792BRU |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 2/33頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT 3CH LP 16-TSSOP |
| 標準包裝： | 96 |
| 位數： | 16 |
| 采樣率（每秒）： | 500 |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 2.5mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 105°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 16-TSSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 3 個差分，單極；3 個差分，雙極 |
| 配用： | EVAL-AD7792EBZ-ND - BOARD EVALUATION FOR AD7792 |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
AD7792/AD7793
Rev. B | Page 9 of 32
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
04
85
5-
00
5
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
CLK
CS
IOUT1
AIN2(+)
AIN1(–)
AIN1(+)
SCLK
DOUT/RDY
DVDD
AVDD
REFIN(–)/AIN3(–)
AIN2(–)
REFIN(+)/AIN3(+)
IOUT2
GND
DIN
AD7792/
AD7793
TOP VIEW
(Not to Scale)
Figure 5. Pin Configuration
Table 4. Pin Function Descriptions
Pin No.
Mnemonic
Description
1
SCLK
Serial Clock Input. This serial clock input is for data transfers to and from the ADC. The SCLK has a Schmitt-
triggered input, making the interface suitable for opto-isolated applications. The serial clock can be
continuous with all data transmitted in a continuous train of pulses. Alternatively, it can be a noncontinuous
clock with the information being transmitted to or from the ADC in smaller batches of data.
2
CLK
Clock In/Clock Out. The internal clock can be made available at this pin. Alternatively, the internal clock can
be disabled, and the ADC can be driven by an external clock. This allows several ADCs to be driven from a
common clock, allowing simultaneous conversions to be performed.
3
CS
Chip Select Input. This is an active low logic input used to select the ADC. CS can be used to select the ADC
in systems with more than one device on the serial bus or as a frame synchronization signal in communicating
with the device. CS can be hardwired low, allowing the ADC to operate in 3-wire mode with SCLK, DIN, and
DOUT used to interface with the device.
4
IOUT1
Output of Internal Excitation Current Source. The internal excitation current source can be made available at
this pin. The excitation current source is programmable so that the current can be 10 μA, 210 μA, or 1 mA.
Either IEXC1 or IEXC2 can be switched to this output.
5
AIN1(+)
Analog Input. AIN1(+) is the positive terminal of the differential analog input pair AIN1(+)/AIN1(
).
6
AIN1(
)
Analog Input. AIN1(
) is the negative terminal of the differential analog input pair AIN1(+)/AIN1().
7
AIN2(+)
Analog Input. AIN2(+) is the positive terminal of the differential analog input pair AIN2(+)/AIN2(
).
8
AIN2(
)
Analog Input. AIN2(
) is the negative terminal of the differential analog input pair AIN2(+)/AIN2().
9
REFIN(+)/AIN3(+)
Positive Reference Input/Analog Input. An external reference can be applied between REFIN(+) and
REFIN(
). REFIN(+) can lie anywhere between AVDD and GND + 0.1 V. The nominal reference voltage
REFIN(+)
REFIN() is 2.5 V, but the part functions with a reference from 0.1 V to AVDD. Alternatively, this pin
can function as AIN3(+) where AIN3(+) is the positive terminal of the differential analog input pair
AIN3(+)/AIN3(
).
10
REFIN(
)/AIN3()
Negative Reference Input/Analog Input. REFIN(
) is the negative reference input for REFIN. This reference
input can lie anywhere between GND and AVDD
0.1 V. This pin also functions as AIN3(), which is the
negative terminal of the differential analog input pair AIN3(+)/AIN3(
).
11
IOUT2
Output of Internal Excitation Current Source. The internal excitation current source can be made available at
this pin. The excitation current source is programmable so that the current can be 10 μA, 210 μA, or 1 mA.
Either IEXC1 or IEXC2 can be switched to this output.
12
GND
Ground Reference Point.
13
AVDD
Supply Voltage, 2.7 V to 5.25 V.
14
DVDD
Digital Interface Supply Voltage. The logic levels for the serial interface pins are related to this supply, which
is between 2.7 V and 5.25 V. The DVDD voltage is independent of the voltage on AVDD; therefore, AVDD can
equal 5 V with DVDD at 3 V or vice versa.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2449IUHF#PBF | IC ADC 24BIT HI SPEED 38QFN |
| VE-26F-IU-S | CONVERTER MOD DC/DC 72V 200W |
| AD7829BRU | IC ADC 8BIT 8CH 2MSPS 28TSSOP |
| LTC2447IUHF#TRPBF | IC ADC 24BIT 8CH HI SPEED 38QFN |
| LTC1867CGN | IC ADC 16BIT 8CH 200KSPS 16SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7792BRU-REEL | 制造商:Analog Devices 功能描述:ADC Single Delta-Sigma 470sps 16-bit Serial 16-Pin TSSOP T/R 制造商:Analog Devices 功能描述:ADC SGL DELTA-SIGMA 0.47KSPS 16BIT SERL 16TSSOP - Tape and Reel |
| AD7792BRUZ | 功能描述:IC ADC 16BIT SIG-DEL 3CH 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD7792BRUZ | 制造商:Analog Devices 功能描述:IC ADC 16BIT 470SPS TSSOP-16 |
| AD7792BRUZ1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:3-Channel, Low Noise, Low Power, 16-/24-Bit ?￡-?? ADC with On-Chip In-Amp and Reference |
| AD7792BRUZ-REEL | 功能描述:IC ADC 16BIT 3CH LP 16-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
發布緊急采購，3分鐘左右您將得到回復。