- 您現在的位置：買賣IC網 > PDF目錄360557 > 908E626 (飛思卡爾半導體(中國)有限公司) Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication PDF資料下載
參數資料
| 型號： | 908E626 |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
| 中文描述： | 集成的步進電機驅動器，帶有嵌入式微控制器和LIN串行通信 |
| 文件頁數： | 26/32頁 |
| 文件大?。?/td> | 303K |
| 代理商： | 908E626 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁
908E626
26
MOTOROLA ANALOG INTEGRATED CIRCUIT DEVICE DATA
Figure 12. BEMF Signal Generation
Half-Bridge Overtemperature Protection
The half-bridge outputs provide an overtemperature pre-
warning with the HTF in the Interrupt Flag Register (IFR). In
order to protect the outputs against overtemperature, the High-
Temperature Reset must be enabled. If this value is reached,
the part generates a reset and disables all power outputs.
Half-Bridge Overcurrent Protection
The half-bridges are protected against short to GND, short to
VSUP, and load shorts.
In the event an overcurrent on the high side is detected, the
high-side MOSFETs on all HB high-side MOSFETs are
switched off automatically. In the event an overcurrent on the
low side is detected, all HB low-side MOSFETs are switched off
automatically. In both cases, the overcurrent status flag
HB_OCF in the System Status Register (SYSSTAT) is set.
The overcurrent status flag is cleared (and the outputs re-
enabled) by writing a logic [1] to the HB_OCF flag in the System
Status Register or by reset.
Half-Bridge Overvoltage/Undervoltage
The half-bridge outputs are protected against undervoltage
and overvoltage conditions. This protection is done by the low-
and high-voltage interrupt circuitry. If one of these flags (LVF,
HVF) is set, the outputs are automatically disabled.
The overvoltage/undervoltage status flags are cleared (and
the outputs re-enabled) by writing a logic [1] to the LVF/HVF
flags in the Interrupt Flag Register or by reset. Clearing this flag
is useless as long as a high- or low-voltage condition is present.
Half-Bridge Control Register (HBCTL)
OFC_EN—H-Bridge Offset Chopping Enable Bit
This read/write bit enables offset chopping. Reset clears the
OFC_EN bit.
1 = Offset chopping enabled.
0 = Offset chopping disabled.
CSA—H-Bridges Current Sense Amplification Select Bit
This read/write bit selects the current sense amplification of
the H-Bridges. Reset clears the CSA bit.
1 = Current sense amplification set for measuring 0.5 A.
0 = Current sense amplification set for measuring 2.5 A.
Coil Current
Voltage on
1
1
BEMF Signal
Register Name and Address: HBCTL - $02
Bit7
6
5
4
3
2
1
Read
OFC_EN
CSA
0
0
0
CLS2
CLS1
CLS0
Write
Reset
0
0
0
0
0
0
0
0
F
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
.
相關PDF資料 |
PDF描述 |
|---|---|
| 908JKJK3JL3FS | 68HC908JK1/JK3/JL3 8-Bit Microcontroller |
| 909-0010 | PUNCH 9 WAY D REAR MOUNT |
| 909-0020 | PUNCH 15 WAY D REAR MOUNT |
| 909-0030 | PUNCH 25 WAY D REAR MOUNT |
| 908-0010 | PUNCH 9 WAY D FRONT MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 908E626_08 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
| 908E626_09 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
| 908E626_12 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
| 908-H003M | 制造商:Farnell / Duratool 功能描述:PICKUP TOOL NUT-LAUNCHER 制造商:Farnell / Duratool 功能描述:PICKUP TOOL, NUT-LAUNCHER 制造商:Farnell / Duratool 功能描述:PICKUP TOOL, NUT-LAUNCHER; Lifter Type:Mechanical; Length:122mm; External Diameter:7mm ;RoHS Compliant: NA |
| 908M 01 2417 HR | 制造商:Taunuslicht 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。