參數資料
型號： 908E626
廠商： 飛思卡爾半導體(中國)有限公司
元件分類： 基準電壓源/電流源
英文描述： Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication
中文描述： 集成的步進電機驅動器，帶有嵌入式微控制器和LIN串行通信
文件頁數： 15/32頁
文件大?。?/td> 303K
代理商： 908E626
MOTOROLA ANALOG INTEGRATED CIRCUIT DEVICE DATA
908E626
15
Current Limitation Frequency Input Terminal (FGEN)
Input terminal for the half-bridge current limitation PWM
frequency. This input is not a real PWM input terminal; it should
just supply the period of the PWM. The duty cycle will be
generated automatically.
Important
The recommended FGEN frequency should be
in the range of 0.1 kHz to 20 kHz.
Back Electromagnetic Force Output Terminal (BEMF)
This terminal gives the user information about back
electromagnetic force (BEMF). This feature allows stall
detection and coil failures in step motor applications. In order to
evaluate this signal the terminal must be directly connected to
terminal PTD0/TACH0/BEMF.
Reset Terminal (
RST_A
)
RST_A
is the bidirectional reset terminal of the analog die. It
is an open drain with pullup resistor and must be connected to
the
RST
terminal of the MCU.
Interrupt Terminal (
IRQ_A
)
IRQ_A
is the interrupt output terminal of the analog die
indicating errors or wake-up events. It is an open drain with
pullup resistor and must be connected to the
IRQ
terminal of the
MCU.
Slave Select Terminal (
SS
)
This terminal is the SPI Slave Select terminal for the analog
chip. All other SPI connections are done internally.
SS
must be
connected to PTB1 or any other logic I/O of the microcontroller.
LIN Bus Terminal (LIN)
The LIN terminal represents the single-wire bus transmitter
and receiver. It is suited for automotive bus systems and is
based on the LIN bus specification.
Half-Bridge Output Terminals (HB1:HB4)
The 908E626 device includes power MOSFETs configured
as four half-bridge driver outputs. The HB1:HB4 outputs may
be configured for step motor drivers, DC motor drivers, or as
high-side and low-side switches.
The HB1:HB4 outputs are short-circuit and overtemperature
protected, and they feature current recopy, current limitation,
and BEMF generation. Current limitation and recopy are done
on the low-side MOSFETs.
Power Supply Terminals (VSUP1:VSUP3)
VSUP1:VSUP3 are device power supply terminals. The
nominal input voltage is designed for operation from 12 V
systems. Owing to the low ON-resistance and current
requirements of the half-bridge driver outputs, multiple VSUP
terminals are provided.
All VSUP terminals must be connected to get full chip
functionality.
Power Ground Terminals (GND1 and GND2)
GND1 and GND2 are device power ground connections.
Owing to the low ON-resistance and current requirements of the
half-bridge driver outputs multiple terminals are provided.
GND1 and GND2 terminals must be connected to get full
chip functionality.
Switchable V
DD
Output Terminal (HVDD)
The HVDD terminal is a switchable V
DD
output for driving
resistive loads requiring a regulated 5.0 V supply; The output is
short-circuit protected.
+5.0 V Voltage Regulator Output Terminal (VDD)
The VDD terminal is needed to place an external capacitor to
stabilize the regulated output voltage. The VDD terminal is
intended to supply the embedded microcontroller.
Important
The VDD terminal should not be used to supply
other loads; use the HVDD terminal for this purpose. The VDD,
EVDD, VDDA, and VREFH terminals must be connected
together.
Voltage Regulator Ground Terminal (VSS)
The VSS terminal is the ground terminal for the connection
of all non-power ground connections (microcontroller and
sensors).
Important
VSS, EVSS, VSSA, and VREFL terminals must
be connected together.
LIN Transceiver Output Terminal (RXD)
This terminal is the output of LIN transceiver. The terminal
must be connected to the microcontroller’s Enhanced Serial
Communications Interface (ESCI) module (RXD terminal).
ADC Reference Terminals (VREFL and VREFH)
VREFL and VREFH are the reference voltage terminals for
the ADC. It is recommended that a high-quality ceramic
decoupling capacitor be placed between these terminals.
Important
VREFH is the high reference supply for the ADC
and should be tied to the same potential as VDDA via separate
traces. VREFL is the low reference supply for the ADC and
should be tied to the same potential as VSS via separate traces.
For details refer to the 68HC908EY16 datasheet.
ADC Supply Terminals (VDDA and VSSA)
VDDA and VSSA
are the power supply terminals for the
analog-to-digital converter (ADC). It is recommended that a
high-quality ceramic decoupling capacitor be placed between
these terminals.
F
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
.
相關PDF資料
PDF描述
908JKJK3JL3FS 68HC908JK1/JK3/JL3 8-Bit Microcontroller
909-0010 PUNCH 9 WAY D REAR MOUNT
909-0020 PUNCH 15 WAY D REAR MOUNT
909-0030 PUNCH 25 WAY D REAR MOUNT
908-0010 PUNCH 9 WAY D FRONT MOUNT
相關代理商/技術參數
參數描述
908E626_08 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication
908E626_09 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication
908E626_12 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication
908-H003M 制造商:Farnell / Duratool 功能描述:PICKUP TOOL NUT-LAUNCHER 制造商:Farnell / Duratool 功能描述:PICKUP TOOL, NUT-LAUNCHER 制造商:Farnell / Duratool 功能描述:PICKUP TOOL, NUT-LAUNCHER; Lifter Type:Mechanical; Length:122mm; External Diameter:7mm ;RoHS Compliant: NA
908M 01 2417 HR 制造商:Taunuslicht 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*