- 您現在的位置：買賣IC網 > PDF目錄360557 > 908E624 (Motorola, Inc.) TRIPLE HIGH-SIDE SWITCH WITH EMBEDDED MCU AND LIN PDF資料下載
參數資料
| 型號： | 908E624 |
| 廠商： | Motorola, Inc. |
| 英文描述： | TRIPLE HIGH-SIDE SWITCH WITH EMBEDDED MCU AND LIN |
| 中文描述： | 三重高邊開關與嵌入式微控制器和LIN |
| 文件頁數： | 18/32頁 |
| 文件大?。?/td> | 453K |
| 代理商： | 908E624 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
Analog Integrated Circuit Device Data
Freescale Semiconductor
18
908E624
Functional Description
Functional Terminal Description
Fast signal transitions on MCU terminals place high, short-
duration current demands on the power supply. To prevent
noise problems, take special care to provide power supply
bypassing at the MCU.
For details refer to the 68HC908EY16 datasheet.
ADC SUPPLY TERMINALS (VDDA AND VSSA)
VDDA and VSSA
are the power supply terminals for the
analog-to-digital converter (ADC). It is recommended that a
high-quality ceramic decoupling capacitor be placed between
these terminals.
Important
VDDA is the supply for the ADC and should be
tied to the same potential as EVDD via separate traces.
VSSA is the ground terminal for the ADC and should be tied
to the same potential as EVSS via separate traces.
For details refer to the 68HC908EY16 datasheet.
ADC REFERENCE TERMINALS (VREFL AND
VREFH)
VREFL and VREFH are the reference voltage terminals for
the ADC. It is recommended that a high-quality ceramic
decoupling capacitor be placed between these terminals.
Important
VREFH is the high reference supply for the
ADC and should be tied to the same potential as VDDA via
separate traces. VREFL is the low reference supply for the
ADC and should be tied to the same potential as VSSA via
separate traces.
For details refer to the 68HC908EY16 datasheet.
TEST TERMINAL (FLSVPP)
This terminal is for test purposes only. Do not connect in
the application.
PWMIN TERMINAL
This terminal is the direct PWM input for high-side
outputs 1 and 2 (HS1 and HS2). If no PWM control is
required, PWMIN must be connected to VDD to enable the
HS1 and HS2 outputs.
LIN TRANSCEIVER OUTPUT TERMINAL (RXD)
This terminal is the output of LIN transceiver. The terminal
must be connected to the microcontroller’s Enhanced Serial
Communications Interface (ESCI) module (RXD terminal).
RESET TERMINAL (
RST_A
)
RST_A
is the reset output terminal of the analog die and
must be connected to the
RST
terminal of the MCU.
Important
To ensure proper operation, do not add any
external pullup resistor.
INTERRUPT TERMINAL (
IRQ_A
)
IRQ_A
is the interrupt output terminal of the analog die
indicating errors or wake-up events. This terminal must be
connected to the
IRQ
terminal of the MCU.
WINDOW WATCHDOG CONFIGURATION
TERMINAL (WDCONF)
This terminal is the configuration terminal for the internal
watchdog. A resistor is connected to this terminal. The
resistor value defines the watchdog period. If the terminal is
open, the watchdog period is fixed to its default value.
The watchdog can be disabled (e.g., for flash
programming or software debugging) by connecting this
terminal to GND.
POWER SUPPLY TERMINALS (VSUP1AND
VSUP2)
This VSUP1 power supply terminal supplies the voltage
regulator, the internal logic, and LIN transceiver.
This VSUP2 power supply terminal is the positive supply
for the high-side switches.
POWER GROUND TERMINAL (GND)
This terminal is the device ground connection.
HIGH-SIDE OUTPUT TERMINALS (HS1 AND HS2)
These terminals are high-side switch outputs to drive loads
such as relays or lamps. Each switch is protected with
overtemperature and current limit (overcurrent). The output
has an internal clamp circuitry for inductive load. The HS1
and HS2 outputs are controlled by SPI and have a direct
enabled input (PWMIN) for PWM capability.
HIGH-SIDE OUTPUT TERMINAL (HS3)
This high-side switch can be used to drive small lamps,
Hall-effect sensors, or switch pullup resistors. The switch is
protected with overtemperature and current limit
(overcurrent). The output is controlled only by SPI.
LIN BUS TERMINAL (LIN)
The LIN terminal represents the single-wire bus
transmitter and receiver. It is suited for automotive bus
systems and is based on the LIN bus specification.
WAKE-UP TERMINALS (L1 AND L2)
These terminals are high-voltage capable inputs used to
sense external switches and to wake up the device from
Sleep or Stop mode. During Normal mode the state of these
terminals can be read through SPI.
相關PDF資料 |
PDF描述 |
|---|---|
| 908E625 | Integrated Quad Half H-Bridge with Power Supply, Embedded MCU, and LIN Serial Communication |
| 908E626 | Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
| 908JKJK3JL3FS | 68HC908JK1/JK3/JL3 8-Bit Microcontroller |
| 909-0010 | PUNCH 9 WAY D REAR MOUNT |
| 909-0020 | PUNCH 15 WAY D REAR MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 908E624_10 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Triple High Side Switch with Embedded MCU and LIN Serial Communicationfor Relay Drivers |
| 908E624_12 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Triple High Side Switch Embedded MCU and Lin Serial Communication for Relay Drivers |
| 908E625 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Quad Half H-Bridge with Power Supply, Embedded MCU, and LIN Serial Communication |
| 908E625_07 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Quad Half H-Bridge with Power Supply, Embedded MCU, and LIN Serial Communication |
| 908E625_10 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Quad Half H-Bridge with Power Supply, Embedded MCU, and LIN Serial Communication |
發布緊急采購，3分鐘左右您將得到回復。