• <form id="2ofug"></form>
    <strike id="2ofug"><kbd id="2ofug"></kbd></strike>
  • <code id="2ofug"><input id="2ofug"><ul id="2ofug"></ul></input></code>
  • <var id="2ofug"></var>
    參數資料
    型號: 7513
    英文描述: 7513 Group Datasheet Datasheet 1067K/FEB.06.01
    中文描述: 7513組數據表數據表1067K/FEB.06.01
    文件頁數: 41/66頁
    文件大?。?/td> 1067K
    代理商: 7513
    40
    SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
    MITSUBISHI MICROCOMPUTERS
    7513 Group
    Voltage Multiplier (3 Times)
    The voltage multiplier performs threefold boosting. This circuit in-
    puts a reference voltage for boosting from LCD power input pin
    V
    L1
    . (However, when using a 1/2 bias, connect V
    L1
    and V
    L2
    and
    apply voltage by external resistor division.)
    Set each bit of the segment output enable register and the LCD
    mode register in the following order for operating the voltage mul-
    tiplier.
    1. Set the segment output enable bits (bits 0 to 5) of the seg-
    ment output enable register to
    0
    or
    1.
    2. Set the duty ratio selection bits (bits 0 and 1), the bias con-
    trol bit (bit 2), the LCD circuit divider division ratio selection
    bits (bits 5 and 6), and the LCDCK count source selection
    bit (bit 7) of the LCD mode register to
    0
    or
    1.
    3. Set the LCD output enable bit (bit 6) of the segment output
    enable register to
    1.
    4. Set the voltage multiplier control bit (bit 4) of the LCD mode
    register to
    1.
    When voltage is input to the V
    L1
    pin during operating the voltage
    multiplier, voltage that is twice as large as V
    L1
    occurs at the V
    L2
    pin, and voltage that is three times as large as V
    L1
    occurs at the
    V
    L3
    pin.
    When using the voltage multiplier, apply 1.3 V
    Voltage
    2.3 V to
    the V
    L1
    pin.
    When not using the voltage multiplier,apply proper voltage to the
    LCD power input pins (V
    L1
    V
    L3
    ). Then set the LCD output enable
    bit to
    1.
    When the LCD output enable bit is set to
    0,
    the V
    CC
    voltage is
    applied to the V
    L3
    pin inside of this microcomputer.
    The voltage multiplier control bit (bit 4 of the LCD mode register)
    controls the voltage multiplier.
    Fig. 42 Example of circuit at each bias
    Table 10 Bias control and applied voltage to V
    L1
    –V
    L3
    Bias value
    1/3 bias
    Voltage value
    V
    L3
    =V
    LCD
    V
    L2
    =2/3 V
    LCD
    V
    L1
    =1/3 V
    LCD
    Note:
    V
    LCD
    is the maximum value of supplied voltage for the LCD panel.
    Bias Control and Applied Voltage to LCD
    Power Input Pins
    To the LCD power input pins (V
    L1
    V
    L3
    ), apply the voltage shown
    in Table 10 according to the bias value.
    Select a bias value by the bias control bit (bit 2 of the LCD mode
    register).
    1/2 bias
    V
    L3
    =V
    LCD
    V
    L2
    =V
    L1
    =1/2 V
    LCD
    V
    L3
    V
    L2
    C
    2
    C
    1
    V
    L1
    1/3 bias
    when using the voltage multiplier
    V
    L3
    V
    L2
    C
    2
    C
    1
    V
    L1
    1/3 bias
    when not using the voltage multiplier
    Open
    Open
    R2
    R1
    R3
    R1=R2=R3
    Contrast control
    V
    L3
    V
    L2
    C
    2
    C
    1
    V
    L1
    1/2 bias
    Open
    Open
    R4
    R5
    R4=R5
    Contrast control
    V
    CC
    V
    CC
    PX
    X
    相關PDF資料
    PDF描述
    75160-101-36 STIFTLEISTE ABTRENNBAR 1REIHIG 36POL
    75160-102-36 STIFTLEISTE ABTRENNBAR 1REIHIG 36POL
    75160-105-36 STIFTLEISTE ABTRENNBAR 1REIHIG 36POL
    75160-301-36 STIFTLEISTE ABTRENNBAR 1REIHIG 36POL
    75160-302-36 STIFTLEISTE ABTRENNBAR 1REIHIG 36POL
    相關代理商/技術參數
    參數描述
    75-130 制造商:Zierick Manufacturing Corporation 功能描述:
    75130-1213 制造商:MOLEX 功能描述:
    75-130477-52S 功能描述:Circular Connector 制造商:amphenol industrial operations 系列:- 包裝:- 零件狀態:有效 連接器類型:- 針腳數:- 外殼尺寸 - 插件:- 外殼尺寸,MIL:- 安裝類型:- 端接:- 緊固類型:- 朝向:- 侵入防護:- 外殼材料,鍍層:- 觸頭鍍層:- 特性:- 觸頭鍍層厚度:- 額定電流:- 電壓 - 額定:- 工作溫度:- 標準包裝:1
    75-131018-1G 制造商:Amphenol Corporation 功能描述:75-131018-01G - Bulk
    75-131018-1I 制造商:Amphenol Corporation 功能描述:75-131018-01I - Bulk