- 您現在的位置：買賣IC網 > PDF目錄360515 > 7513 7513 Group Datasheet Datasheet 1067K/FEB.06.01 PDF資料下載
參數資料
| 型號： | 7513 |
| 英文描述： | 7513 Group Datasheet Datasheet 1067K/FEB.06.01 |
| 中文描述： | 7513組數據表數據表1067K/FEB.06.01 |
| 文件頁數： | 27/66頁 |
| 文件大?。?/td> | 1067K |
| 代理商： | 7513 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁
26
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
7513 Group
Timer Y
Timer Y is a 16-bit timer that can be selected in one of four modes.
(1) Timer Mode
The timer counts f(X
IN
)/16 (or f(X
CIN
)/16 in low-speed mode).
(2) Period Measurement Mode
CNTR
1
interrupt request is generated at rising/falling edge of
CNTR
1
pin input signal. Simultaneously, the value in timer Y latch
is reloaded in timer Y and timer Y continues counting down. Ex-
cept for the above-mentioned, the operation in period
measurement mode is the same as in timer mode.
The timer value just before the reloading at rising/falling of CNTR
1
pin input signal is retained until the timer Y is read once after the
reload.
The rising/falling timing of CNTR
1
pin input signal is found by
CNTR
1
interrupt. When using a timer in this mode, set the port
shared with the CNTR
1
pin to input.
(3) Event Counter Mode
The timer counts signals input through the CNTR
1
pin.
Except for this, the operation in event counter mode is the same
as in timer mode. When using a timer in this mode, set the port
shared with the CNTR
1
pin to input.
(4) Pulse Width HL Continuously Measurement
Mode
CNTR
1
interrupt request is generated at both rising and falling
edges of CNTR
1
pin input signal. Except for this, the operation in
pulse width HL continuously measurement mode is the same as in
period measurement mode. When using a timer in this mode, set
the port shared with the CNTR
1
pin to input.
I
Notes on CNTR
1
interrupt active edge selection
CNTR
1
interrupt active edge depends on the CNTR
1
active edge
switch bit. However, in pulse width HL continuously measurement
mode, CNTR
1
interrupt request is generated at both rising and
falling edges of CNTR
1
pin input signal regardless of the setting of
CNTR
1
active edge switch bit.
Fig. 21 Structure of timer Y mode register
Timer Y mode register
(TYM : address 0028
16
)
b7
b0
Not used (return
“
0
”
when read)
Timer Y operating mode bits
b5 b4
0 0 : Timer mode
0 1 : Period measurement mode
1 0 : Event counter mode
1 1 : Pulse width HL continuously
measurement mode
CNTR
1
active edge switch bit
0 : Count at rising edge in event counter mode
Measure the falling edge to falling edge
period in period measurement mode
Falling edge active for CNTR
1
interrupt
1 : Count at falling edge in event counter mode
Measure the rising edge period in period
measurement mode
Rising edge active for CNTR
1
interrupt
Timer Y stop control bit
0 : Count start
1 : Count stop
相關PDF資料 |
PDF描述 |
|---|---|
| 75160-101-36 | STIFTLEISTE ABTRENNBAR 1REIHIG 36POL |
| 75160-102-36 | STIFTLEISTE ABTRENNBAR 1REIHIG 36POL |
| 75160-105-36 | STIFTLEISTE ABTRENNBAR 1REIHIG 36POL |
| 75160-301-36 | STIFTLEISTE ABTRENNBAR 1REIHIG 36POL |
| 75160-302-36 | STIFTLEISTE ABTRENNBAR 1REIHIG 36POL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 75-130 | 制造商:Zierick Manufacturing Corporation 功能描述: |
| 75130-1213 | 制造商:MOLEX 功能描述: |
| 75-130477-52S | 功能描述:Circular Connector 制造商:amphenol industrial operations 系列:- 包裝:- 零件狀態:有效 連接器類型:- 針腳數:- 外殼尺寸 - 插件:- 外殼尺寸，MIL:- 安裝類型:- 端接:- 緊固類型:- 朝向:- 侵入防護:- 外殼材料，鍍層:- 觸頭鍍層:- 特性:- 觸頭鍍層厚度:- 額定電流:- 電壓 - 額定:- 工作溫度:- 標準包裝:1 |
| 75-131018-1G | 制造商:Amphenol Corporation 功能描述:75-131018-01G - Bulk |
| 75-131018-1I | 制造商:Amphenol Corporation 功能描述:75-131018-01I - Bulk |
發布緊急采購，3分鐘左右您將得到回復。