- 您現在的位置：買賣IC網 > PDF目錄18687 > 73S1210F-68MR/F/PG (Maxim Integrated)IC SOC SMART CARD READER 68QFN PDF資料下載
參數資料
| 型號： | 73S1210F-68MR/F/PG |
| 廠商： | Maxim Integrated |
| 文件頁數： | 97/126頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SOC SMART CARD READER 68QFN |
| 標準包裝： | 2,500 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁當前第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁
73S1210F Data Sheet
DS_1210F_001
72
Rev. 1.4
1.7.15.2
Answer to Reset Processing
A card insertion event generates an interrupt to the firmware, which is then responsible for the
configuration of the electrical interface, the UART and activation of the card. The activation sequencer
goes through the power up sequence as defined in the ISO 7816-3 specification. An asynchronous
activation timing diagram is shown in
Figure 16. After the card reset is de-asserted, the firmware instructs the hardware to look for a TS byte
that begins the ATR response. If a response is not provided within the pre-programmed timeout period,
an interrupt is generated and the firmware can then take appropriate action, including instructing the
73S1210F to begin a deactivation sequence. Once commanded, the deactivation sequencer goes
through the power down sequence as defined in the ISO 7816-3 specification. If an ATR response is
received, the hardware looks for a TS byte that determines direct/inverse convention. The hardware
handles the indirect convention conversion such that the embedded firmware only receives direct
convention. This feature can be disabled by firmware within SByteCtl register. Parity checking and
break generation is performed on the TS byte unless disabled by firmware. If during the card session, a
card removal, over-current or other error event is detected, the hardware will automatically perform the
deactivation sequence and then generate an interrupt to the firmware. The firmware can then perform
any other error handling required for proper system operation. Smart card RST, I/O and CLK, C4, C8
shall be low before the end of the deactivation sequence. Figure 17 shows the timing for a deactivation
sequence.
VCCSEL
bits
VCC
VCCOK bit
RSTCRD bit
RST
CLK
IO
t1
t2
t3
t4
t5
tto
See Note
ATR starts
t4
SELSC
bits
t1: SELSC.1 bit set (selects internal ICC interface) and a non-zero value in VCCSEL bits (calling for a
value of Vcc of 1.8, 3.0, or 5.0 volts) will begin the activation sequence. t1 is the time for Vcc to rise
to acceptable level, declared as Vcc OK (bit VCCOK gets set). This time depends on filter capacitor
value and card Icc load.
tto: The time allowed for Vcc to rise to Vcc OK status after setting of the VCCSEL bits. This time is
generated by the VCCTMR counter. If Vcc OK is not set, (bit VCCOK) at this time, a deactivation will
be initiated. VCCSEL bits are not automatically cleared. The firmware must clear the VCCSEL bits
before starting a new activation.
t2: Time from VccTmr timeout and VCC OK to IO reception (high), typically 2-3 CLK cycles if RDYST
= 0. If RDYST = 1, t2 starts when VCCOK = 1.
t3: Time from IO = high to CLK start, typically 2-3 CLK cycles.
t4: Time allowed for start of CLK to de-assertion of RST. Programmable by the RLength register.
t5: Time allowed for ATR timeout, set by the STSTO register.
Note: If the RSTCRD bit is set, RST is asserted (low). Upon clearing RSTCRD bit, RST will be
de-asserted after t4.
相關PDF資料 |
PDF描述 |
|---|---|
| XRCWHT-L1-0000-00601 | LED COOL WHITE 500MA 7X9 SMD |
| 73S1210F-44M/F/PC | IC SOC SMART CARD READER 44QFN |
| XRCWHT-L1-0000-00403 | LED COOL WHITE 500MA 7X9 SMD |
| XRCWHT-L1-0000-00302 | LED COOL WHITE 500MA 7X9 SMD |
| XRCWHT-L1-0000-00301 | LED COOL WHITE 500MA 7X9 SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 73S1210F-EB | 功能描述:開發板和工具包 - 8051 73S1210F Eval Brd (Doc. Cd, Cable) RoHS:否 制造商:Silicon Labs 產品:Development Kits 工具用于評估:C8051F960, Si7005 核心: 接口類型:USB 工作電源電壓: |
| 73S1210F-EB-Lite | 功能描述:開發板和工具包 - 8051 73S1210F Eval Brd Lite w/Doc Cd, Cable RoHS:否 制造商:Silicon Labs 產品:Development Kits 工具用于評估:C8051F960, Si7005 核心: 接口類型:USB 工作電源電壓: |
| 73S1210F-EB-LiteMS | 功能描述:開發板和工具包 - 8051 73S1210F Eval Brd Lite + Multi Sam RoHS:否 制造商:Silicon Labs 產品:Development Kits 工具用于評估:C8051F960, Si7005 核心: 接口類型:USB 工作電源電壓: |
| 73S1215F | 制造商:TERIDIAN 制造商全稱:TERIDIAN 功能描述:80515 System-on-Chip with USB, ISO 7816 / EMV, PINpad and More |
| 73S1215F-44IM/F | 功能描述:8位微控制器 -MCU 80515 SoC w/USB & PINpad RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。