- 您現在的位置：買賣IC網 > PDF目錄298505 > 72841L10PF (INTEGRATED DEVICE TECHNOLOGY INC) 4K X 9 BI-DIRECTIONAL FIFO, 6.5 ns, PQFP64 PDF資料下載
參數資料
| 型號： | 72841L10PF |
| 廠商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分類： | FIFO |
| 英文描述： | 4K X 9 BI-DIRECTIONAL FIFO, 6.5 ns, PQFP64 |
| 封裝： | TQFP-64 |
| 文件頁數： | 10/16頁 |
| 文件大?。?/td> | 211K |
| 代理商： | 72841L10PF |
3
IDT72801/728211/72821/72831/72841/72851 DUAL CMOS SyncFIFOTM
DUAL 256 x 9, DUAL 512 x 9, DUAL 1K x 9, DUAL 2K x 9, DUAL 4K x 9, DUAL 8K x 9
COMMERCIAL AND INDUSTRIAL
TEMPERATURERANGES
Symbol
Name
I/O
Description
DA0-DA8
A Data Inputs
I
9-bit data inputs to RAM array A.
DB0-DB8
B Data Inputs
I
9-bit data inputs to RAM array B.
RSA, RSB
Reset
I
When RSA (RSB) is set LOW, the associated internal read and write pointers of array A (B) are set to
the first location; FFA (FFB) and PAFA (PAFB) go HIGH, and PAEA (PAEB) and EFA (EFB) go
LOW. After power-up, a reset of both FIFOs A and B is required before an initial Write.
WCLKA
WriteClock
I
Data is written into the FIFO A (B) on a LOW-to-HIGH transition of WCLKA (WCLKB) when the write
WCLKB
enable(s) are asserted.
WENA1
Write Enable 1
I
If FIFO A (B) is configured to have programmable flags, WENA1 (WENB1) is the only Write
WENB1
Enable pin that can be used. When WENA1 (WENB1) is LOW, data A (B) is written into the FIFO
on every LOW-to-HIGH transition WCLKA (WCLKB). If the FIFO is configured to have two write enables,
WENA1 (WENB1) must be LOW and WENA2 (WENB2) must be HIGH to write data into the FIFO. Data
will not be written into the FIFO if FFA (FFB) is LOW.
WENA2/LDA
Write Enable 2/
I
FIFO A (B) is configured at reset to have either two write enables or programmable flags. If LDA (LDB)
WENB2/LDB
Load
is HIGH at reset, this pin operates as a second write enable. If WENA2/LDA (WENB2/LDB) is LOW
at reset this pin operates as a control to load and read the programmable flag offsets for its respective array.
If the FIFO is configured to have two write enables, WENA1 (WENB1) must be LOW
and WENA2 (WENB2) must be HIGH to write data into FIFO A (B). Data will not be written into FIFO A (B)
if FFA (FFB) is LOW. If the FIFO is configured to have programmable flags, LDA
(LDB) is held
LOW to write or read the programmable flag offsets.
QA0-QA8
A Data Outputs
O
9-bit data outputs from RAM array A.
QB0-QB8
B Data Outputs
O
9-bit data outputs from RAM array B.
RCLKA
Read Clock
I
Data is read from FIFO A (B) on a LOW-to-HIGH transition of RCLKA (RCLKB) when RENA1
RCLKB
(RENB1) and RENA2 (RENB2) are asserted.
RENA1
Read Enable 1
I
When RENA1 (RENB1) and RENA2 (RENB2) are LOW, data is read from FIFO A (B) on every
RENB1
LOW-to-HIGH transition of RCLKA (RCLKB). Data will not be read from Array A (B) if EFA (EFB) is LOW.
RENA2
Read Enable 2
I
When RENA1 (RENB1) and RENA2 (RENB2) are LOW, data is read from the FIFO A (B) on every
RENB2
LOW-to-HIGH transition of RCLKA (RCLKB). Data will not be read from array A (B) if the EFA (EFB) is LOW.
OEA
OutputEnable
I
When OEA (OEB) is LOW, outputs DA0-DA8 (DB0-DB8) are active. If OEA (OEB) is HIGH, the
OEB
outputs DA0-DA8 (DB0-DB8) will be in a high-impedance state.
EFA
Empty Flag
O
When EFA (EFB) is LOW, FIFO A (B) is empty and further data reads from the output are inhibited.
EFB
When EFA (EFB) is HIGH, FIFO A (B) is not empty. EFA (EFB) is synchronized to RCLKA (RCLKB).
PAEA
Programmable
O
When PAEA (PAEB) is LOW, FIFO A (B) is almost-empty based on the offset programmed into the
PAEB
Almost-Empty
appropriate offset register. The default offset at reset is Empty+7. PAEA (PAEB) is synchronized to
Flag
RCLKA (RCLKB).
PAFA
Programmable
O
When PAFA (PAFB) is LOW, FIFO A (B) is almost-full based on the offset programmed into the appropriate
PAFB
Almost-FullFlag
offset register. The default offset at reset is Full-7. PAFA (PAFB) is synchronized to WCLKA (WCLKB).
FFA
Full Flag
O
When FFA (FFB) is LOW, FIFO A (B) is full and further data writes into the input are inhibited.
FFB
When FFA (FFB) is HIGH, FIFO A (B) is not full. FFA (FFB) is synchronized to WCLKA (WCLKB).
VCC
Power
+5V power supply pin.
GND
Ground
0V ground pin.
PIN DESCRIPTIONS
The IDT72801/72811/72821/72831/72841/72851s two FIFOs, referred
to as FIFO A and FIFO B, are identical in every respect. The following
description defines the input and output signals for FIFO A. The correspond-
ing signal names for FIFO B are provided in parentheses.
相關PDF資料 |
PDF描述 |
|---|---|
| 72821L15TF8 | 1K X 9 BI-DIRECTIONAL FIFO, 10 ns, PQFP64 |
| 72R99-P | 25 A, BARRIER STRIP TERMINAL BLOCK, 1 ROW, 1 DECK |
| 72R99-M | 25 A, BARRIER STRIP TERMINAL BLOCK, 1 ROW, 1 DECK |
| 72R99-59 | 25 A, BARRIER STRIP TERMINAL BLOCK, 1 ROW, 1 DECK |
| 72R99-49 | 25 A, BARRIER STRIP TERMINAL BLOCK, 1 ROW, 1 DECK |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 72841L10PF8 | 功能描述:先進先出 RoHS:否 制造商:IDT 電路數量: 數據總線寬度:18 bit 總線定向:Unidirectional 存儲容量:4 Mbit 定時類型:Synchronous 組織:256 K x 18 最大時鐘頻率:100 MHz 訪問時間:10 ns 電源電壓-最大:3.6 V 電源電壓-最小:6 V 最大工作電流:35 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-80 封裝: |
| 72841L10PFG | 功能描述:先進先出 RoHS:否 制造商:IDT 電路數量: 數據總線寬度:18 bit 總線定向:Unidirectional 存儲容量:4 Mbit 定時類型:Synchronous 組織:256 K x 18 最大時鐘頻率:100 MHz 訪問時間:10 ns 電源電壓-最大:3.6 V 電源電壓-最小:6 V 最大工作電流:35 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-80 封裝: |
| 72841L10PFG8 | 制造商:Integrated Device Technology Inc 功能描述:FIFO Mem Sync Quad Depth/Width Bi-Dir 4K x 9 x 2 64-Pin TQFP T/R 制造商:Integrated Device Technology Inc 功能描述:FIFO SYNC QUAD DEPTH/WIDTH BI-DIR 4KX9X2 64TQFP - Tape and Reel |
| 72841L10TF | 功能描述:先進先出 RoHS:否 制造商:IDT 電路數量: 數據總線寬度:18 bit 總線定向:Unidirectional 存儲容量:4 Mbit 定時類型:Synchronous 組織:256 K x 18 最大時鐘頻率:100 MHz 訪問時間:10 ns 電源電壓-最大:3.6 V 電源電壓-最小:6 V 最大工作電流:35 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-80 封裝: |
| 72841L10TF8 | 制造商:Integrated Device Technology Inc 功能描述:FIFO Mem Sync Quad Depth/Width Bi-Dir 4K x 9 x 2 64-Pin STQFP T/R 制造商:Integrated Device Technology Inc 功能描述:FIFO SYNC QUAD DEPTH/WIDTH BI-DIR 4KX9X2 64TQFP - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。