- 您現在的位置：買賣IC網 > PDF目錄358933 > LPC47B34X (STANDARD MICROSYSTEMS CORP) 128 Pin Enhanced Super I/O with LPC Interface for Consumer Applications PDF資料下載
參數資料
| 型號： | LPC47B34X |
| 廠商： | STANDARD MICROSYSTEMS CORP |
| 元件分類： | 外設及接口 |
| 英文描述： | 128 Pin Enhanced Super I/O with LPC Interface for Consumer Applications |
| 中文描述： | MULTIFUNCTION PERIPHERAL, PQFP128 |
| 封裝： | QFP-128 |
| 文件頁數： | 68/250頁 |
| 文件大?。?/td> | 645K |
| 代理商： | LPC47B34X |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁當前第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁第231頁第232頁第233頁第234頁第235頁第236頁第237頁第238頁第239頁第240頁第241頁第242頁第243頁第244頁第245頁第246頁第247頁第248頁第249頁第250頁
68
goes high, the SE bit in Status Register 0 is set to "1" and the command is terminated. If the nTRK0
pin is still low after 79 step pulses have been issued, the FDC sets the SE and the EC bits of Status
Register 0 to "1" and terminates the command. Disks capable of handling more than 80 tracks per
side may require more than one Recalibrate command to return the head back to physical Track 0.
The Recalibrate command does not have a result phase. The Sense Interrupt Status command must
be issued after the Recalibrate command to effectively terminate it and to provide verification of the
head position (PCN). During the command phase of the recalibrate operation, the FDC is in the BUSY
state, but during the execution phase it is in a NON-BUSY state. At this time, another Recalibrate
command may be issued, and in this manner parallel Recalibrate operations may be done on up to
four drives at once. Upon power up, the software must issue a Recalibrate command to properly
initialize all drives and the controller.
Seek
The read/write head within the drive is moved from track to track under the control of the Seek
command. The FDC compares the PCN, which is the current head position, with the NCN and
performs the following operation if there is a difference:
PCN < NCN: Direction signal to drive set to "1" (step in) and issues step pulses.
PCN > NCN: Direction signal to drive set to "0" (step out) and issues step pulses.
The rate at which step pulses are issued is controlled by SRT (Stepping Rate Time) in the Specify
command. After each step pulse is issued, NCN is compared against PCN, and when NCN = PCN the
SE bit in Status Register 0 is set to "1" and the command is terminated. During the command phase
of the seek or recalibrate operation, the FDC is in the BUSY state, but during the execution phase it is
in the NON-BUSY state. At this time, another Seek or Recalibrate command may be issued, and in
this manner, parallel seek operations may be done on up to four drives at once.
Note that if implied seek is not enabled, the read and write commands should be preceded by:
1) Seek command - Step to the proper track
2) Sense Interrupt Status command - Terminate the Seek command
3) Read ID - Verify head is on proper track
4) Issue Read/Write command.
The Seek command does not have a result phase. Therefore, it is highly recommended that the
Sense Interrupt Status command is issued after the Seek command to terminate it and to provide
verification of the head position (PCN). The H bit (Head Address) in ST0 will always return to a "0".
When exiting POWERDOWN mode, the FDC clears the PCN value and the status information to zero.
Prior to issuing the POWERDOWN command, it is highly recommended that the user service all
pending interrupts through the Sense Interrupt Status command.
相關PDF資料 |
PDF描述 |
|---|---|
| LPC47B37X | 100 Pin Enhanced Super I/O for LPC Bus with SMBus Controller for Commercial Applications |
| LPC47M14X-NC | 128 PIN ENGANCED SUPER I/O CONTROLLER WITH AN LPC INTERFACE AND USB HUB |
| LPC47M14Y-NC | 128 PIN ENGANCED SUPER I/O CONTROLLER WITH AN LPC INTERFACE AND USB HUB |
| LPC47M14Z-NC | 128 PIN ENGANCED SUPER I/O CONTROLLER WITH AN LPC INTERFACE AND USB HUB |
| LPC47M14C-NC | BNC MALE TO RJ11/SCREW TESCA-BL10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LPC47B351-NC | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| LPC47B357-NC | 制造商:SMSC 功能描述:ELECTRONIC COMPONENT |
| LPC47B373QFP | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:SMSC 功能描述: |
| LPC47B373QFP WAF | 制造商:SMSC 功能描述: |
| LPC47B377QFP | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:SMSC 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。