- 您現在的位置：買賣IC網 > PDF目錄368730 > 16F872 (Microchip Technology Inc.) CAT 5E CROSSOVER PATCH CORD CABLE GREEN 10 FT PDF資料下載
參數資料
| 型號： | 16F872 |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | CAT 5E CROSSOVER PATCH CORD CABLE GREEN 10 FT |
| 中文描述： | 28引腳，8位閃存微控制器的CMOS |
| 文件頁數： | 71/160頁 |
| 文件大?。?/td> | 2600K |
| 代理商： | 16F872 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁當前第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁
1999 Microchip Technology Inc.
Preliminary
DS30221A-page 71
PIC16F872
9.2.11
I
2
C MASTER MODE TRANSMISSION
Transmission of a data byte, a 7-bit address or either
half of a 10-bit address, is accomplished by simply writ-
ing a value to SSPBUF register. This action will set the
buffer full flag (BF) and allow the baud rate generator to
begin counting and start the next transmission. Each
bit of address/data will be shifted out onto the SDA pin
after the falling edge of SCL is asserted (see data hold
time spec). SCL is held low for one baud rate gener-
ator rollover count (T
BRG
). Data should be valid before
SCL is released high (see data setup time spec).
When the SCL pin is released high, it is held that way
for T
BRG
. The data on the SDA pin must remain stable
for that duration and some hold time after the next fall-
ing edge of SCL. After the eighth bit is shifted out (the
falling edge of the eighth clock), the BF flag is cleared
and the master releases SDA allowing the slave device
being addressed to respond with an ACK bit during the
ninth bit time, if an address match occurs or if data was
received properly. The status of ACK is read into the
ACKDT on the falling edge of the ninth clock. If the
master receives an acknowledge, the acknowledge
status bit (ACKSTAT) is cleared. If not, the bit is set.
After the ninth clock, the SSPIF is set and the master
clock (baud rate generator) is suspended until the next
data byte is loaded into the SSPBUF, leaving SCL low
and SDA unchanged (
Figure 9-14
).
After the write to the SSPBUF, each bit of address will
be shifted out on the falling edge of SCL until all seven
address bits and the R/W bit are completed. On the fall-
ing edge of the eighth clock, the master will de-assert
the SDA pin allowing the slave to respond with an
acknowledge. On the falling edge of the ninth clock, the
master will sample the SDA pin to see if the address
was recognized by a slave. The status of the ACK bit is
loaded into the ACKSTAT status bit (SSPCON2<6>).
Following the falling edge of the ninth clock transmis-
sion of the address, the SSPIF is set, the BF flag is
cleared, and the baud rate generator is turned off until
another write to the SSPBUF takes place, holding SCL
low and allowing SDA to float.
9.2.11.7
BF STATUS FLAG
In Transmit mode, the BF bit (SSPSTAT<0>) is set
when the CPU writes to SSPBUF and is cleared when
all 8 bits are shifted out.
9.2.11.8
WCOL STATUS FLAG
If the user writes the SSPBUF when a transmit is
already in progress (i.e., SSPSR is still shifting out a
data byte), then WCOL is set and the contents of the
buffer are unchanged (the write doesn’t occur).
WCOL must be cleared in software.
9.2.11.9
ACKSTAT STATUS FLAG
In Transmit mode, the ACKSTAT bit (SSPCON2<6>) is
cleared when the slave has sent an acknowledge
(ACK = 0) and is set when the slave does not acknowl-
edge (ACK = 1). A slave sends an acknowledge when
it has recognized its address (including a general call)
or when the slave has properly received its data.
相關PDF資料 |
PDF描述 |
|---|---|
| 16F876A | 28/40-pin Enhanced FLASH Microcontrollers |
| 16F876 | CAT 5E CROSSOVER, GREEN 15 FT PATCH CABLE |
| 16F877 | CAT 5E CROSSOVER PATCH CORD CABLE GREEN 20 FT |
| 16FL100S02 | 6A, 12A AND 16A FAST RECOVERY RECTIFIERS |
| 16FL100S05 | 6A, 12A AND 16A FAST RECOVERY RECTIFIERS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 16F876 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:28/40-pin 8-Bit CMOS FLASH Microcontrollers |
| 16F876A | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:28/40-pin Enhanced FLASH Microcontrollers |
| 16F877 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:28/40-pin 8-Bit CMOS FLASH Microcontrollers |
| 16F9040 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:COMPACT DIGITALMULTIMETER TRUE RMS |
| 16F9041 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:COMPACT DMM MIT RS232 |
發布緊急采購，3分鐘左右您將得到回復。