參數資料
型號： 16F872
廠商： Microchip Technology Inc.
英文描述： CAT 5E CROSSOVER PATCH CORD CABLE GREEN 10 FT
中文描述： 28引腳，8位閃存微控制器的CMOS
文件頁數： 70/160頁
文件大?。?/td> 2600K
代理商： 16F872
PIC16F872
DS30221A-page 70
Preliminary
1999 Microchip Technology Inc.
9.2.10
I
2
C MASTER MODE REPEATED START
CONDITION TIMING
A Repeated Start condition occurs when the RSEN bit
(SSPCON2<1>) is programmed high and the I
2
C mod-
ule is in the idle state. When the RSEN bit is set, the
SCL pin is asserted low. When the SCL pin is sampled
low, the baud rate generator is loaded with the contents
of SSPADD<6:0> and begins counting. The SDA pin is
released (brought high) for one baud rate generator
count (T
BRG
). When the baud rate generator times out
if SDA is sampled high, the SCL pin will be deasserted
(brought high). When SCL is sampled high the baud
rate generator is reloaded with the contents of
SSPADD<6:0> and begins counting. SDA and SCL
must be sampled high for one T
BRG
. This action is then
followed by assertion of the SDA pin (SDA is low) for
one T
BRG
, while SCL is high. Following this, the RSEN
bit in the SSPCON2 register will be automatically
cleared and the baud rate generator will not be
reloaded, leaving the SDA pin held low. As soon as a
start condition is detected on the SDA and SCL pins,
the S bit (SSPSTAT<3>) will be set. The SSPIF bit will
not be set until the baud rate generator has timed-out.
Immediately following the SSPIF bit getting set, the
user may write the SSPBUF with the 7-bit address in
7-bit mode, or the default first address in 10-bit mode.
After the first eight bits are transmitted and an ACK is
received, the user may then transmit an additional eight
bits of address (10-bit mode) or eight bits of data (7-bit
mode).
9.2.10.6
WCOL STATUS FLAG
If the user writes the SSPBUF when a Repeated Start
sequence is in progress, then WCOL is set and the
contents of the buffer are unchanged (the write doesn’t
occur).
FIGURE 9-13: REPEAT START CONDITION WAVEFORM
Note 1:
If RSEN is programmed while any other
event is in progress, it will not take effect.
Note 2:
A bus collision during the Repeated Start
condition occurs if:
SDA is sampled low when SCL goes
from low to high.
SCL goes low before SDA is asserted
low. This may indicate that another
master is attempting to transmit a
data "1".
Note:
Because queueing of events is not
allowed, writing of the lower 5 bits of
SSPCON2 is disabled until the Repeated
Start condition is complete.
SDA
SCL
Sr = Repeated Start
Write to SSPCON2
occurs here.
Write to SSPBUF occurs here.
Falling edge of ninth clock
End of Xmit
At completion of start bit,
hardware clear RSEN bit
and set SSPIF
1st Bit
Set S (SSPSTAT<3>)
T
BRG
T
BRG
SDA = 1,
SCL(no change)
SDA = 1,
SCL = 1
T
BRG
T
BRG
T
BRG
相關PDF資料
PDF描述
16F876A 28/40-pin Enhanced FLASH Microcontrollers
16F876 CAT 5E CROSSOVER, GREEN 15 FT PATCH CABLE
16F877 CAT 5E CROSSOVER PATCH CORD CABLE GREEN 20 FT
16FL100S02 6A, 12A AND 16A FAST RECOVERY RECTIFIERS
16FL100S05 6A, 12A AND 16A FAST RECOVERY RECTIFIERS
相關代理商/技術參數
參數描述
16F876 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:28/40-pin 8-Bit CMOS FLASH Microcontrollers
16F876A 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:28/40-pin Enhanced FLASH Microcontrollers
16F877 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:28/40-pin 8-Bit CMOS FLASH Microcontrollers
16F9040 制造商:未知廠家 制造商全稱:未知廠家 功能描述:COMPACT DIGITALMULTIMETER TRUE RMS
16F9041 制造商:未知廠家 制造商全稱:未知廠家 功能描述:COMPACT DMM MIT RS232
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*