
m
PD78P048A
29
9. ELECTRICAL SPECIFICATIONS
Absolute Maximum Ratings (T
A
= 25 °C)
Parameter
Symbol
Conditions
Rating
Unit
Supply voltage
V
DD
–0.3 to +7.0
V
V
LOAD
V
DD
–40 to V
DD
+0.3
V
V
PP
–0.3 to 13.5
V
AV
DD
–0.3 to V
DD
+0.3
V
AV
REF
–0.3 to V
DD
+0.3
V
AV
SS
–0.3 to +0.3
V
Input voltage
V
I1
P00 to P04, P10 to P17, P20 to P27, P30 to P37, X1, X2,
XT2, RESET
–0.3 to V
DD
+0.3
V
V
I2
P70-P74
N-ch open drain
–0.3 to +16
V
V
I3
P110 to P117, P120 to P127
P-ch open drain
V
DD
–40 to V
DD
+0.3
V
Output voltage
V
O1
P01 to P03, P10 to P17, P20 to P27, P30 to P37
–0.3 to V
DD
+0.3
V
V
O2
P70 to P74
–0.3 to +16
V
V
OD
P80, P81, P90 to P97, P100 to P107, P110 to P117, P120 to P127
V
DD
–40 to V
DD
+0.3
V
Analog input voltage
V
AN
ANI0 to ANI7
Analog input pins
AV
SS
–0.3 to AV
REF0
+0.3
V
High-level
output current
I
OH
1 pin of P01 to P03, P10 to P17, P20 to P27, P30 to P37
–10
mA
Total for P01 to P03, P10 to P17,
P0 to P27, P30 to P37
–30
mA
1 pin of P80, P81, P90 to P97, P100 to P107, P110 to P117, P120 to P127
–30
mA
Total for P80, P81, P90 to P97, P100 to P107, P110 to P117, P120 to P127
–120
mA
Low-level
output current
I
OL
Note 1
1 pin of P01 to P03, P10 to P17, P20 to
P27, P30 to P37, P70 to P74
Peak value
30
mA
rms
15
mA
Total for P01 to P03, P10 to P17,
P20 to P27, P30 to P37
Peak value
50
mA
rms
20
mA
Total for P56, P57, P60 to P63
Peak value
100
mA
rms
60
mA
Total for P70 to P74
Peak value
100
mA
rms
60
mA
Total power
dissipation
P
T
Note 2
T
A
= –40 to +60 °C
800
mW
T
A
= +85 °C
600
mW
T
A
–40 to +85
°C
Storage temperature
T
stg
–65 to +150
°C
Caution Product quality may suffer if the absolute maximum rating is exceeded for even a single parameter,
or even momentarily. In other words, the absolute maximum ratings are rated values at which the
product is on the verge of suffering physical damage, and therefore the product must be used under
conditions which ensure that the absolute maximum ratings are not exceeded.
Remark
Unless specified otherwise, dual-function pin characteristics are the same as port pin characteristics.
Notes 1.
The rms should be calculated as follows: [rms value] = [Peak value]
¥
÷
Duty
Operating ambient
temperature