- 您現在的位置：買賣IC網 > PDF目錄376462 > XRT75VL00 (Exar Corporation) E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR PDF資料下載
參數資料
| 型號： | XRT75VL00 |
| 廠商： | Exar Corporation |
| 英文描述： | E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR |
| 中文描述： | E3/DS3/STS-1線路接口單元與抖動衰減器 |
| 文件頁數： | 32/50頁 |
| 文件大小： | 268K |
| 代理商： | XRT75VL00 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
XRT75VL00
E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
REV. 1.0.3
30
5.2
The Clock and Data Recovery Circuit extracts the embedded clock, from the sliced digital data stream and
provides the retimed data to the B3ZS (HDB3) decoder.
The Clock Recovery PLL can be in one of the following two modes:
T
RAINING
M
ODE
:
In the absence of input signals at RTIP and RRing pins, or when the frequency difference between the
recovered line clock signal and the reference clock applied on the ExClk input pin exceed 0.5%, the clock
recovery unit enters into Training Mode and a Loss of Lock condition is declared by toggling RLOL output pin
“High” (in Hardware Mode) or setting the RLOL bit to “1” in the control registers (in Host Mode). Also, the clock
output on the RxClk pin is the same as the reference clock applied on ExClk pin.
D
ATA
/C
LOCK
R
ECOVERY
M
ODE
:
In the presence of input line signals on the RTIP and RRing input pins and when the frequency difference
between the recovered clock signal and the reference clock signal is less than 0.5%, the clock that is output on
the RxClk out pin is the Recovered Clock signal.
5.3
B3ZS/HDB3 Decoder:
The decoder block takes the output from clock and data recovery block and decodes the B3ZS (for DS3 or
STS-1) or HDB3 (for E3) encoded line signal and detects any coding errors or excessive zeros in the data
stream.
Whenever the input signal violates the B3ZS or HDB3 coding sequence for bipolar violation or contains three
(for B3ZS) or four (for HDB3) or more consecutive zeros, an active “High” pulse is generated on the RLCV
output pins to indicate line code violation.
N
OTE
:
In Single- Rail (NRZ) mode, the decoder is bypassed.
5.4
LOS (Loss of Signal) Detector:
5.4.1
DS3/STS-1 LOS Condition:
A Digital Loss of Signal (DLOS) condition occurs when a string of 175 ± 75 consecutive zeros occur on the line.
When the DLOS condition occurs, the DLOS bit is set to “1” in the status control register. DLOS condition is
cleared when the detected average pulse density is greater than 33% for 175 ± 75 pulses.
Analog Loss of Signal (ALOS) condition occurs when the amplitude of the incoming line signal is below the
threshold as shown in the Table 10.The status of the ALOS condition is reflected in the ALOS status control
register.
Clock and Data Recovery:
T
ABLE
9: I
NTERFERENCE
M
ARGIN
T
EST
R
ESULTS
M
ODE
C
ABLE
L
ENGTH
(A
TTENUATION
)
I
NTERFERENCE
T
OLERANCE
E3
0 dB
-14 dB
12 dB
-18 dB
DS3
0 feet
-17 dB
225 feet
-16 dB
450 feet
-16 dB
STS-1
0 feet
-16 dB
225 feet
-15 dB
450 feet
-15 dB
相關PDF資料 |
PDF描述 |
|---|---|
| XRT75VL00IV | E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR |
| XRT79L71 | 1 - CHANNEL DS3/E3 ATM UNI/PPP COMBO IC |
| XRT79L71IB | 1 - CHANNEL DS3/E3 ATM UNI/PPP COMBO IC |
| XRT79L72 | 2 - CHANNEL DS3/E3 ATM UNI/PPP COMBO IC |
| XRT79L72IB | 2 - CHANNEL DS3/E3 ATM UNI/PPP COMBO IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT75VL00_08 | 制造商:EXAR 制造商全稱:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR |
| XRT75VL00D | 制造商:EXAR 制造商全稱:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER |
| XRT75VL00D_08 | 制造商:EXAR 制造商全稱:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET |
| XRT75VL00D1V-F | 制造商:Exar Corporation 功能描述: |
| XRT75VL00DES | 功能描述:時鐘合成器/抖動清除器 1CHT3/E3/STS1LIU+ DESYNC 3.3V DRV VER RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。