參數資料
型號: XRT75R03DIV
廠商: EXAR CORP
元件分類: 數字傳輸電路
英文描述: THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCRONIZER
中文描述: DATACOM, PCM TRANSCEIVER, PQFP128
封裝: 14 X 20 MM, LQFP-128
文件頁數: 123/134頁
文件大?。?/td> 803K
代理商: XRT75R03DIV
XRT75R03D
REV. 1.0.2
THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCRONIZER
118
10.7.2
Wander Measurement test results will be provided in the next revision of the XRT75R03D Data Sheet.
10.8
Designing with the XRT75R03D
In this section, we will discuss the following topics.
How to design with and configure the XRT75R03D to permit a system to meet the above-mentioned Intrinsic
Jitter and Wander requirements.
How is the XRT75R03D able to meet the above-mentioned requirements
How does the XRT75R03D permits the user to comply with the SONET APS Recovery Time requirements of
50ms (per Telcordia GR-253-CORE)
How should one configure the XRT75R03D, if one needs to support "Daisy-Chain" Testing at the end
Customer’s site
10.8.1
How to design and configure the XRT75R03D to permit a system to meet the above-
mentioned Intrinsic Jitter and Wander requirements
As mentioned earlier, in most application (in which the XRT75R03D will be used in a SONET De-Sync
Application) the user will typically interface the XRT75R03D to a Mapper device in the manner as presented
below in Figure 58.
In this application, the Mapper has the responsibility of receiving a SONET STS-N/OC-N signal and extracting
as many as N DS3 signals from this signal. As a given channel within the Mapper IC extracts out a given DS3
signal (from SONET) it will typically be applying a Clock and Data signal to the "Transmit Input" of the LIU IC.
Figure 58 presents a simple illustration as to how one channel, within the XRT75R03D should be connected to
the Mapper IC.
Wander Measurement Test Results
As mentioned above, the Mapper IC will typically output a Clock and Data signal to the XRT75R03D. In many
cases, the Mapper IC will output the contents of an entire STS-1 data-stream via the Data Signal to the
XRT75R03D. However, the Mapper IC typically only supplies a clock pulse via the Clock Signal to the
XRT75R03D coincident to whenever a DS3 bit is being output via the Data Signal. In this case, the Mapper IC
would not supply a clock edge coincident to when a TOH, POH or any non-DS3 data-bit is being output via the
Data-Signal.
F
IGURE
58. I
LLUSTRATION
OF
THE
XRT75R03D
BEING
CONNECTED
TO
A
M
APPER
IC
FOR
SONET D
E
-S
YNC
A
PPLICATIONS
IC
DS3 to STS-N
Mapper/
Demapper
XRT75R03D
STS-N Signal
TPDATA_n input pin
TCLK_n input
De-Mapped (Gapped)
DS3 Data and Clock
相關PDF資料
PDF描述
XRT75R03 THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
XRT75R03IV THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
XRT75R06D SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
XRT75R06DIB SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
XRT75R06 SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
相關代理商/技術參數
參數描述
XRT75R03DIV-F 功能描述:網絡控制器與處理器 IC 3-Ch E3/DS3/STS-1 RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
XRT75R03DIVTR 功能描述:時鐘合成器/抖動清除器 3CHNNEL E3/DS3/STS 1 JITTER ATTENUATOR RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75R03DIVTR-F 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
XRT75R03ES 功能描述:時鐘合成器/抖動清除器 3CH T3/E3/STS1LIU+JA 3.3V W/REDUNDANCY RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75R03IV 功能描述:外圍驅動器與原件 - PCI 3CHNNEL E3/DS3/STS 1 JITTER ATTENUATOR RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray