JITTER
參數資料
型號： XRT75L02IV-F
廠商： Exar Corporation
文件頁數： 29/50頁
文件大?。?/td> 0K
描述： IC LIU E3/DS3/STS-1 2CH 100TQFP
標準包裝： 90
類型： 線路接口裝置（LIU）
驅動器/接收器數： 2/2
規程： DS3，E3，STS-1
電源電壓： 3.135 V ~ 3.465 V
安裝類型： 表面貼裝
封裝/外殼： 100-LQFP
供應商設備封裝： 100-TQFP（14x14）
包裝： 托盤
XRT75L02
xr
TWO CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER
REV. 1.0.3
33
6.2
JITTER TRANSFER - RECEIVER/TRANSMITTER:
Jitter Transfer function is defined as the ratio of jitter on the output relative to the jitter applied on the input
versus frequency.
There are two distinct characteristics of jitter transfer: i) jitter gain (jitter peaking) defined as the highest ratio
above 0dB; and ii) jitter transfer bandwidth.The overall jitter transfer bandwidth is controlled by a low bandwidth
loop, typically using a voltage-controller crystal oscillator (VCXO).
The jitter transfer function is a ratio between the jitter output and jitter input for a component, or system often
expressed in dB. A negative dB jitter transfer indicates the element removed jitter. A positive dB jitter transfer
indicates the element added jitter. A zero dB jitter transfer indicates the element had no effect on jitter.
Table 12 shows the jitter transfer characteristics and/or jitter attenuation specifications for various data rates:
The above specifications can be met only with a jitter attenuator that supports E3/DS3/STS-1 rates.
6.3
JITTER GENERATION:
Jitter Generation is defined as the process whereby jitter appears at the output port of the digital equipment in
the absence of applied input jitter. Jitter Generation is measured by sending jitter free data to the clock and
data recovery circuit and measuring the amount of jitter on the output clock or the re-timed data. Since this is
essentially a noise measurement, it requires a definition of bandwidth to be meaningful. The bandwidth is set
according to the data rate. In general, the jitter is measured over a band of frequencies.
6.4
Jitter Attenuator:
An advanced crystal-less jitter attenuator per channel is included in the XRT75L02. The jitter attenuator
requires no external crystal nor high-frequency reference clock.
In Host mode, by clearing or setting the JATx/Rx_n bits in the channel control registers selects the jitter
attenuator either in the Receive or Transmit path on per channel basis. In Hardware mode, JATx/Rx pin selects
globally all three channels either in Receive or Transmit path.
The FIFO size can be either 16-bit or 32-bit. In HOST mode, the bits JA0_n and JA1_n can be set to
appropriate combination to select the different FIFO sizes or to disable the Jitter Attenuator on a per channel
basis. In Hardware mode, appropriate setting of the pins JA0 and JA1 selects the different FIFO sizes or
disables the Jitter Attenuator for all the channels. Data is clocked into the FIFO with the associated clock signal
(TxClk or RxClk) and clocked out of the FIFO with the dejittered clock. When the FIFO is within two bits of
TABLE 11: JITTER AMPLITUDE VERSUS MODULATION FREQUENCY (JITTER TOLERANCE)
BIT RATE
(KB/S)
STANDARD
INPUT JITTER AMPLITUDE (UI
P
-P)
MODULATION FREQUENCY
A1
A2
A3
F
1(HZ)
F
2(HZ)
F
3(KHZ)
F
4(KHZ)
F
5(KHZ)
34368
ITU-T G.823
1.5
0.15
-
100
1000
10
800
-
44736
GR-499
CORE Cat I
5
0.1
-
10
2.3k
60
300
-
44736
GR-499
CORE Cat II
10
0.3
-
10
669
22.3
300
-
51840
GR-253
CORE Cat II
15
1.5
0.15
10
30
300
2
20
TABLE 12: JITTER TRANSFER SPECIFICATION/REFERENCES
E3
DS3
STS-1
ETSI TBR-24
GR-499 CORE section 7.3.2
Category I and Category II
GR-253 CORE section 5.6.2.1
相關PDF資料
PDF描述
MS3101F22-12S CONN RCPT 5POS FREE HNG W/SCKT
M83723/75A14126 CONN PLUG 12POS STRAIGHT W/SCKT
MS3106A20-15SW CONN PLUG 7POS STRAIGHT W/SCKT
XRT83L38IB IC LIU T1/E1/J1 OCTAL 225BGA
IDT72V3660L10PF8 IC FIFO SS 4096X36 10NS 128-TQFP
相關代理商/技術參數
參數描述
XRT75L02IVTR-F 功能描述:時鐘合成器/抖動清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75L03 制造商:EXAR 制造商全稱:EXAR 功能描述:THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
XRT75L03D 制造商:EXAR 制造商全稱:EXAR 功能描述:THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
XRT75L03DES 功能描述:時鐘合成器/抖動清除器 3 CH T3/E3/STS1 LIU+DESYNCH3.3V RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75L03DIV 功能描述:外圍驅動器與原件 - PCI 3CHNNEL E3/DS3/STS 1 SONET DE-SYNCH RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*