- 您現在的位置：買賣IC網 > PDF目錄9995 > XRT75L02IV-F (Exar Corporation)IC LIU E3/DS3/STS-1 2CH 100TQFP PDF資料下載
參數資料
| 型號： | XRT75L02IV-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 25/50頁 |
| 文件大小： | 0K |
| 描述： | IC LIU E3/DS3/STS-1 2CH 100TQFP |
| 標準包裝： | 90 |
| 類型： | 線路接口裝置（LIU） |
| 驅動器/接收器數： | 2/2 |
| 規程： | DS3，E3，STS-1 |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 100-LQFP |
| 供應商設備封裝： | 100-TQFP（14x14） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
XRT75L02
xr
TWO CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER
REV. 1.0.3
29
TRAINING MODE:
In the absence of input signals at RTIP_n and RRING_n pins, or when the frequency difference between the
recovered line clock signal and the reference clock applied on the E3/DS3/STS1CLK input pins exceed 0.5%,
a Loss of Lock condition is declared by toggling RLOL_n output pin “High” (in Hardware Mode) or setting the
RLOL_n bit to “1” in the control registers. Also, the clock output on the RxClk_n pins are the same as the
reference clock applied on E3/DS3/STS1CLK pins.
DATA/CLOCK RECOVERY MODE:
In the presence of input line signals on the RTIP_n and RRING_n input pins and when the frequency
difference between the recovered clock signal and the reference clock signal is less than 0.5%, the clock that
is output on the RxClk_n out pins is the Recovered Clock signal.
5.3
B3ZS/HDB3 Decoder:
The decoder block takes the output from clock and data recovery block and decodes the B3ZS (for DS3 or
STS-1) or HDB3 (for E3) encoded line signal and detects any coding errors or excessive zeros in the data
stream.
When the input signal violates the B3ZS or HDB3 coding sequence for bipolar violation or contains three (for
B3ZS) or four (for HDB3) or more consecutive zeros, an active “High” pulse is generated on the RLCV_n
output pins to indicate line code violation.
NOTE: In Single- Rail (NRZ) mode, the decoder is bypassed.
5.4
LOS (Loss of Signal) Detector:
5.4.1
DS3/STS-1 LOS Condition:
A Digital Loss of SIgnal (DLOS) condition occurs when a string of 175 ± 75 consecutive zeros occur on the line.
When the DLOS condition occurs, the DLOS_n bit is set to “1” in the status control register. DLOS condition is
cleared when the detected average pulse density is greater than 33% for 175 ± 75 pulses.
Analog Loss of Signal (ALOS) condition occurs when the amplitude of the incoming line signal is below the
threshold as shown in the Table 10.The status of the ALOS condition is reflected in the ALOS_n status control
register.
RLOS is the logical OR of the DLOS and ALOS states. When the RLOS condition occurs the RLOS_n output
pin is toggled “High” and the RLOS_n bit is set to “1” in the status control register.
DISABLING ALOS/DLOS DETECTION:
For debugging purposes it is useful to disable the ALOS and/or DLOS detection. Setting both ALOSDIS_n and
DLOSDIS_n bits disables the LOS detection on a per channel basis.
5.4.2
E3 LOS Condition:
If the level of incoming line signal drops below the threshold as described in the ITU-T G.775 standard, the
LOS condition is detected. Loss of signal level is defined to be between 15 and 35 dB below the normal level.
If the signal drops below 35 dB for 175 ± 75 consecutive pulse periods, LOS condition is declared. This is
illustrated in Figure 19.
TABLE 10: THE ALOS (ANALOG LOS) DECLARATION AND CLEARANCE THRESHOLDS FOR A GIVEN SETTING OF
REQEN (DS3 AND STS-1 APPLICATIONS)
APPLICATION
REQEN S
SIGNAL LEVEL TO DECLARE ALOS SIGNAL LEVEL TO CLEAR ALOS
DS3
0
<17 mV
>70 mV
1
<20 mV
>90 mV
STS-1
0
<20 mV
>90 mV
1
<25 mV
>115 mV
相關PDF資料 |
PDF描述 |
|---|---|
| MS3101F22-12S | CONN RCPT 5POS FREE HNG W/SCKT |
| M83723/75A14126 | CONN PLUG 12POS STRAIGHT W/SCKT |
| MS3106A20-15SW | CONN PLUG 7POS STRAIGHT W/SCKT |
| XRT83L38IB | IC LIU T1/E1/J1 OCTAL 225BGA |
| IDT72V3660L10PF8 | IC FIFO SS 4096X36 10NS 128-TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT75L02IVTR-F | 功能描述:時鐘合成器/抖動清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| XRT75L03 | 制造商:EXAR 制造商全稱:EXAR 功能描述:THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR |
| XRT75L03D | 制造商:EXAR 制造商全稱:EXAR 功能描述:THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER |
| XRT75L03DES | 功能描述:時鐘合成器/抖動清除器 3 CH T3/E3/STS1 LIU+DESYNCH3.3V RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| XRT75L03DIV | 功能描述:外圍驅動器與原件 - PCI 3CHNNEL E3/DS3/STS 1 SONET DE-SYNCH RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。