參數資料
型號: XRT73R06IB
廠商: Exar Corporation
文件頁數: 5/68頁
文件大?。?/td> 0K
描述: IC LIU E3/DS3/STS-1 6CH 217BGA
標準包裝: 126
類型: 線路接口裝置(LIU)
驅動器/接收器數: 6/6
規程: DS3,E3,STS-1
電源電壓: 3.135 V ~ 3.465 V
安裝類型: 表面貼裝
封裝/外殼: 217-BBGA
供應商設備封裝: 217-BGA(23x23)
包裝: 托盤
á
XRT73R06
SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT
REV. 1.0.0
10
C9
T8
D12
R11
C11
R9
RLOL_0
RLOL_1
RLOL_2
RLOL_3
RLOL_4
RLOL_5
O
Receive Loss of Lock - Channel 0:
Receive Loss of Lock - Channel 1:
Receive Loss of Lock - Channel 2:
Receive Loss of Lock - Channel 3:
Receive Loss of Lock - Channel 4:
Receive Loss of Lock - Channel 5:
This output pin toggles "High" if a Loss of Lock Condition is detected. LOL
(Loss of Lock) condition occurs if the recovered clock frequency deviates from
the Reference Clock frequency (available at either E3CLK or DS3CLK or STS-
1CLK input pins) by more than 0.5%.
L16
RXA
****
External Resistor of 3.01K
± 1%.
Should be connected between RxA and RxB for internal bias.
K16
RXB
****
External Resistor of 3.01K
±1%.
Should be connected between RxA and RxB for internal bias.
P12
ICT
I
In-Circuit Test Input:
Setting this pin "Low" causes all digital and analog outputs to go into a high-
impedance state to allow for in-circuit testing. For normal operation, tie this pin
"High".
NOTE: This pin is internally pulled up.
R12
TEST
****
Factory Test Pin
NOTE: This pin must be connected to GND for normal operation.
MICROPROCESSOR INTERFACE
LEAD #
SIGNAL NAME
TYPE
DESCRIPTION
K3
CS
I
Chip Select
Tie this “Low” to enable the communication with the Microprocessor Interface.
R1
PCLK
I
Processor Clock Input
To operate the Microprocessor Interface, appropriate clock frequency is pro-
vided through this pin. Maximum frequency is 66 Mhz.
K2
WR
I
Write Data :
To write data into the registers, this active low signal is asserted.
L2
RD
I
Read Data:
To read data from the registers, this active low pin is asserted.
J3
RESET
I
Register Reset:
Setting this input pin "Low" resets the contents of the Command Registers to
their default settings and default operating configuration
NOTE: This pin is internally pulled up.
L3
PMODE
I
Processor Mode Select:
When this pin is tied “High”, the microprocessor is operating in synchronous
mode which means that clock must be applied to the PCLK (pin 55).
Tie this pin “Low” to select the Asynchronous mode. An internal clock is pro-
vided for the microprocessor interface.
CONTROL AND ALARM INTERFACE
相關PDF資料
PDF描述
XRT73L03BIV IC LIU E3/DS3/STS-1 3CH 120LQFP
IDT72825LB15PF IC FIFO SYNC DL 1024X18 128TQFP
MS27472T12F35P CONN RCPT 22POS WALL MNT W/PINS
IDT72V3650L6PFG8 IC FIFO SS 2048X36 6NS 128-TQFP
MS3100A28-2P CONN RCPT 14POS WALL MNT W/PINS
相關代理商/技術參數
參數描述
XRT73R06IB-F 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT73R12 制造商:EXAR 制造商全稱:EXAR 功能描述:TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT
XRT73R12_07 制造商:EXAR 制造商全稱:EXAR 功能描述:TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT
XRT73R12_0710 制造商:EXAR 制造商全稱:EXAR 功能描述:TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT
XRT73R12ES 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray