LEAD
參數資料
型號: XRT73R06IB
廠商: Exar Corporation
文件頁數: 3/68頁
文件大小: 0K
描述: IC LIU E3/DS3/STS-1 6CH 217BGA
標準包裝: 126
類型: 線路接口裝置(LIU)
驅動器/接收器數: 6/6
規程: DS3,E3,STS-1
電源電壓: 3.135 V ~ 3.465 V
安裝類型: 表面貼裝
封裝/外殼: 217-BBGA
供應商設備封裝: 217-BGA(23x23)
包裝: 托盤
á
XRT73R06
SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT
REV. 1.0.0
8
CLOCK INTERFACE
LEAD #
SIGNAL NAME
TYPE
DESCRIPTION
E15
E3CLK
I
E3 Clock Input (34.368 MHz ± 20 ppm):
If any of the channels is configured in E3 mode, a reference clock 34.368 MHz
is applied on this pin.
NOTE: In single frequency mode, this reference clock is not required.
G16
DS3CLK
I
DS3 Clock Input (44.736 MHz ± 20 ppm):
If any of the channels is configured in DS3 mode, a reference clock 44.736
MHz. is applied on this pin.
NOTE: In single frequency mode, this reference clock is not required.
C16
STS-1CLK/
12M
I
STS-1 Clock Input (51.84 MHz ± 20 ppm):
If any of the channels is configured in STS-1 mode, a reference clock 51.84
MHz is applied on this pin..
In Single Frequency Mode, a reference clock of 12.288 MHz ± 20 ppm is con-
nected to this pin and the internal clock synthesizer generates the appropriate
clock frequencies based on the configuration of the channels in E3, DS3 or
STS-1 modes.
L15
SFM_EN
I
Single Frequency Mode Enable:
Tie this pin “High” to enable the Single Frequency Mode. A reference clock of
12.288 MHz ± 20 ppm is applied.
In the Single Frequency Mode (SFM) a low jitter output clock is provided for
each channel if the CLK_EN bit is set thus eliminating the need for a separate
clock source for the framer.
Tie this pin “Low” if single frequency mode is not selected. In this case, the
appropriate reference clocks must be provided.
NOTE:
This pin is internally pulled down
B1
T1
B17
T17
D11
P11
CLKOUT_0
CLKOUT_1
CLKOUT_2
CLKOUT_3
CLKOUT_4
CLKOUT_5
O
Clock output for channel 0
Clock output for channel 1
Clock output for channel 2
Clock output for channel 3
Clock output for channel 4
Clock output for channel 5
Low jitter clock output for each channel based on the mode selection (E3,DS3
or STS-1) if the CLKOUTEN_n bit is set in the control register.
This eliminates the need for a separate clock source for the framer.
NOTES:
1.
The maximum drive capability for the clockouts is 16 mA.
2.
This clock out is available both in SFM and non-SFM modes.
相關PDF資料
PDF描述
XRT73L03BIV IC LIU E3/DS3/STS-1 3CH 120LQFP
IDT72825LB15PF IC FIFO SYNC DL 1024X18 128TQFP
MS27472T12F35P CONN RCPT 22POS WALL MNT W/PINS
IDT72V3650L6PFG8 IC FIFO SS 2048X36 6NS 128-TQFP
MS3100A28-2P CONN RCPT 14POS WALL MNT W/PINS
相關代理商/技術參數
參數描述
XRT73R06IB-F 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT73R12 制造商:EXAR 制造商全稱:EXAR 功能描述:TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT
XRT73R12_07 制造商:EXAR 制造商全稱:EXAR 功能描述:TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT
XRT73R12_0710 制造商:EXAR 制造商全稱:EXAR 功能描述:TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT
XRT73R12ES 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray