- 您現在的位置：買賣IC網 > PDF目錄9994 > XRT73LC03AIV (Exar Corporation)IC LIU E3/DS3/STS-1 3CH 120LQFP PDF資料下載
參數資料
| 型號： | XRT73LC03AIV |
| 廠商： | Exar Corporation |
| 文件頁數： | 35/61頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LIU E3/DS3/STS-1 3CH 120LQFP |
| 標準包裝： | 72 |
| 類型： | 線路接口裝置（LIU） |
| 驅動器/接收器數： | 3/3 |
| 規程： | DS3，E3，STS-1 |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 120-LQFP |
| 供應商設備封裝： | 120-LQFP（14x20） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁
XRT73LC03A
38
3 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
REV. 1.0.4
3.3
CLOCK RECOVERY PLL
The purpose of the Clock Recovery PLL is to track
the incoming Dual-Rail data stream and to derive and
generate a recovered clock signal.
It is important to note that the Clock Recovery PLL re-
quires a line rate clock signal at the EXClk_(n) input
pin.
The Clock Recovery PLL operates in one of two
modes:
The Training Mode.
The Data/Clock Recovery Mode
3.3.1
The Training Mode
If a given channel is not receiving a line signal via the
RTIP and RRing input pins, or if the frequency differ-
ence between the line signal and that applied via the
EXClk_(n) input pin exceeds 0.5%, then the channel
operates in the Training Mode. When the channel is
operating in the Training Mode, it does the following:
a. Declare a Loss of Lock indication by toggling its
respective RLOL_(n) output pin “High".
b. Output a clock signal via the RxClk_(n) output
pins which is derived from the signal applied to
the EXClk_(n) input pin.
3.3.2
The Data/Clock Recovery Mode
If the frequency difference between the line signal
and that applied via the EXClk_(n) input pin is less
than 0.5%, then the channel operates in the Data/
Clock Recovery mode. In this mode, the Clock Re-
covery PLL locks onto the line signal via the RTIP
and RRing input pins.
3.4
THE HDB3/B3ZS DECODER
The Remote Transmitting Terminal typically encodes
the line signal into some sort of Zero Suppression
Line Code (e.g., HDB3 for E3, and B3ZS for DS3 and
STS-1). The purpose of this encoding activity was to
aid in the Clock Recovery process of this data within
the Near-End Receiving Terminal. However, once the
data has made it across the E3, DS3 or STS-1 Trans-
port Medium and has been recovered by the Clock
Recovery PLL, it is now necessary to restore the orig-
inal content of the data. Hence, the purpose of the
HDB3/B3ZS Decoding block is to restore the data
transmitted over the E3, DS3 or STS-1 line to its orig-
inal content prior to Zero Suppression Coding.
3.4.1
B3ZS Decoding (DS3/STS-1 Applications)
If the XRT73LC03A is configured to operate in the
DS3 or STS-1 Modes, then the HDB3/B3ZS Decod-
ing Blocks performs B3ZS Decoding. When the De-
coders are operating in this mode, each of the De-
coders parses through its respective incoming Dual-
Rail data and checks for the occurrence of either a
“00V" or a "B0V" pattern. If the B3ZS Decoder de-
tects this particular pattern, then it substitutes these
bits with a "000" pattern.
NOTE: If the B3ZS Decoder detects any bipolar violations
that is not in accordance with the B3ZS Line Code format,
or if the B3ZS Decoder detects a string of 3 (or more) con-
secutive "0’s” in the incoming line signal, then the B3ZS
Decoder flags this event as a Line Code Violation by puls-
ing the LCV output pin “High".
Figure 24 illustrates the B3ZS Decoder at work with
two separate Zero Suppression patterns in the incom-
ing Dual-Rail Data Stream.
3.4.2
HDB3 Decoding (E3 Applications)
If the XRT73LC03A is configured to operate in the E3
Mode, then each of the HDB3/B3ZS Decoding Blocks
performs HDB3 Decoding. When the Decoders are
operating in this mode, they each parse through the
incoming Dual-Rail data and check for the occurrence
of either a "000V" or a "B00V" pattern. If the HDB3
FIGURE 24. AN EXAMPLE OF B3ZS DECODING
Data
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
RPOS
RNEG
0 0
V
Line Signal
B
0 V
RCLK
相關PDF資料 |
PDF描述 |
|---|---|
| MS3101A22-20S | CONN RCPT 9POS FREE HNG W/SCKT |
| IDT72V263L10PFI8 | IC FIFO 8192X18 10NS 80QFP |
| VI-B6B-IV-F1 | CONVERTER MOD DC/DC 95V 150W |
| IDT72615L50PF8 | IC FIFO BY SYNC 512X18X2 64QFP |
| MS27656T15F5PB | CONN RCPT 5POS WALL MNT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT73LC03AIVF | 制造商:Exar Corporation 功能描述:Line Interface Unit 51.84Mbps DS3/E3/STS-1 Serial 120-Pin LQFP |
| XRT73LC03AIV-F | 功能描述:外圍驅動器與原件 - PCI 3-Ch DS3, E3, STS-1 RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT73LC04A | 制造商:EXAR 制造商全稱:EXAR 功能描述:4 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT |
| XRT73LC04A_08 | 制造商:EXAR 制造商全稱:EXAR 功能描述:4 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT |
| XRT73LC04AES | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。