- 您現在的位置：買賣IC網 > PDF目錄376461 > XRT7302 (Exar Corporation) 2 Channel E3/DS3/STS-1 Line Interface Unit(2通道 E3/DS3/STS-1線接口單元) PDF資料下載
參數資料
| 型號： | XRT7302 |
| 廠商： | Exar Corporation |
| 英文描述： | 2 Channel E3/DS3/STS-1 Line Interface Unit(2通道 E3/DS3/STS-1線接口單元) |
| 中文描述： | 2頻道E3/DS3/STS-1線路接口單元（2通道E3/DS3/STS-1線接口單元） |
| 文件頁數： | 58/62頁 |
| 文件大?。?/td> | 715K |
| 代理商： | XRT7302 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁當前第58頁第59頁第60頁第61頁第62頁
XRT7302
2 CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT
á
PRELIMINARY
REV. P1.1.6
54
Bit D3 - STS-1/(DS3_(n)) - Channel(n) - Mode Se-
lect
This Read/Write bit field is used to configure Chan-
nel(n) to operate in either the SONET STS-1 Mode or
the DS3 Mode.
Writing a "0" into this bit-field configures Channel(n)
to operate in the DS3 Mode. Writing a "1" into this
bit-field configures Channel(n) to operate in the SO-
NET STS-1 Mode.
N
OTE
:
This bit-field is ignored if the E3_Ch(n) bit-field (e.g.,
D2 in this Command Register) is set to "1".
Bit D2 - E3 Mode Select - Channel(n)
This Read/Write bit-field is used to configure Chan-
nel(n) to operate in the E3 Mode.
Writing a "0" into this bit-field configures Channel(n)
to operate in either the DS3 or SONET STS-1 Mode
as specified by the setting of the DS3 bit-field in this
Command Register. Writing a "1" into this bit-field
configures Channel(n) to operate in the E3 Mode.
Bit D1 - LLB(n) (Local Loop-Back - Channel(n))
This Read/Write bit-field along with RLB(n) is used to
configure Channel(n) to operate in any one of a vari-
ety of Loop-Back modes.
Table 8 relates the contents of LLB(n) and RLB(n)
and the corresponding Loop-Back mode for Chan-
nel(n).
Bit D0 - RLB(n) (Remote Loop-Back - Channel(n))
This Read/Write bit-field along with LLB(n) is used to
configure Channel(n) to operate in any one of a vari-
ety of Loop-Back modes.
Table 8 relates the contents of LLB(n) and RLB(n)
and the corresponding Loop-Back mode for Chan-
nel(n).
5.3
O
PERATING
THE
M
ICROPROCESSOR
S
ERIAL
I
NTERFACE
.
The XRT7302 Serial Interface is a simple four wire in-
terface that is compatible with many of the micro-con-
trollers available in the market. This interface con-
sists of the following signals:
CS - Chip Select (Active Low)
SClk - Serial Clock
SDI - Serial Data Input
SDO - Serial Data Output
Using the Microprocessor Serial Interface
The following instructions for using the Microproces-
sor Serial Interface are best understood by referring
to the diagram in Figure 31 and the timing diagram in
Figure 32.
In order to use the Microprocessor Serial Interface, a
clock signal must be first applied to the SClk input pin.
Then, initiate a Read or Write operation by asserting
the active-low Chip Select input pin CS. It is impor-
tant to assert the CS pin (e.g., toggle it “Low") at least
50ns prior to the very first rising edge of the clock sig-
nal.
Once the CS input pin has been asserted, the type of
operation and the target register address must now
be specified. Provide this information to the Micro-
processor Serial Interface by writing eight serial bits
of data into the SDI input.
N
OTE
:
Each of these bits is clocked into the SDI input on
the rising edge of SClk.
Bit 1- R/W (Read/Write) Bit
This bit is clocked into the SDI input on the first rising
edge of SClk after CS has been asserted. This bit in-
dicates whether the current operation is a Read or
Write operation. A "1" in this bit specifies a Read op-
eration, a "0" in this bit specifies a Write operation.
Bits 2 through 5: The four (4) bit Address Values
(labeled A0, A1, A2 and A3)
The next four rising edges of the SClk signal clocks in
the 4-bit address value for this particular Read or
Write operation. The address selects the Command
Register in the XRT7302 that the user either be read-
ing data from or writing data to. The address bits
must be applied to the SDI input pin in ascending or-
der with the LSB (least significant bit) first.
Bit 6 and 7:
T
ABLE
8: C
ONTENTS
OF
LLB(
N
)
AND
RLB(
N
)
AND
THE
C
ORRESPONDING
L
OOP
-B
ACK
M
ODE
FOR
C
HANNEL
(
N
)
LLB
(n)
RLB
(n)
L
OOP
-B
ACK
M
ODE
(
FOR
C
HANNEL
(n)
)
0
0
None
1
0
Analog Loop-Back Mode (See Section 4.1 for Details)
1
1
Digital Loop-Back Mode (See Section 4.2 for Details
0
1
Remote Loop-Back Mode (See Section 4.3 for Details
相關PDF資料 |
PDF描述 |
|---|---|
| XRT73L02M | TWO CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT |
| XRT73L02MIV | TWO CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT |
| XRT73L02 | 2 Channel E3/DS3/STS-1 Line Interface Unit(2通道 E3/DS3/STS-1線接口單元) |
| XRT73L03A | 3 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT |
| XRT73L03AIV | 3 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT7302IV | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PCM Transceiver |
| XRT73L00 | 制造商:EXAR 制造商全稱:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT |
| XRT73L00A | 制造商:EXAR 制造商全稱:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT |
| XRT73L00AES | 功能描述:界面開發工具 Eval System for XRT73L00A Series RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XRT73L00AIV | 制造商:EXAR 制造商全稱:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT |
發布緊急采購，3分鐘左右您將得到回復。