- 您現在的位置：買賣IC網 > PDF目錄2018 > XRD9836ACG (Exar Corporation)IC 16B CCD/CIS SIG PROC 48TSSOP PDF資料下載
參數資料
| 型號： | XRD9836ACG |
| 廠商： | Exar Corporation |
| 文件頁數： | 6/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC 16B CCD/CIS SIG PROC 48TSSOP |
| 產品變化通告： | Leaded UART, V&I Obsolescence 11/Apr/2011 |
| 標準包裝： | 39 |
| 位數： | 16 |
| 通道數： | 3 |
| 功率（瓦特）： | 500mW |
| 電壓 - 電源，模擬： | 3 V ~ 3.6 V |
| 電壓 - 電源，數字： | 3 V ~ 3.6 V |
| 封裝/外殼： | 48-TSSOP（0.240"，6.10mm 寬） |
| 供應商設備封裝： | 48-TSSOP |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
XRD9836
xr
16-BIT PIXEL GAIN AFE
REV. 1.0.0
14
TIMING - CLOCK BASICS:
The XRD9836 has 4 clock signals BSAMP, VSAMP,
ADCLK and LCLMP. These inputs control the sam-
pling, clamping and synchronization functions of the
device.
The pixel rate clocks are BSAMP, VSAMP and AD-
CLK. BSAMP controls the sampling of the black refer-
ence level of a CCD input signal. VSAMP controls the
sampling of the video level of a CCD or CIS output
signal. The ADCLK controls the internal sampling of
the PGA by the ADC and ADC operation.
The line rate clock, LCLMP, performs the clamping
and synchronization functions. The clamp function
sets the bias point for the external AC coupling ca-
pacitor on the inputs. Synchronization defines the odd
pixel in the APOAM mode.
CLOCK POLARITY
Each of the 4 timing signals has a separate polarity
control bit in the CONTROL register. Figure 10 shows
the logic implementation of the polarity control. If the
polarity bit is low (default) BSAMP and VSAMP sam-
ple on the falling edge, LCLMP is active high and AD-
CLK must be low during the VSAMP falling edge. See
timing examples if Figure 17 and Figure 18
If any of the external timing signals are inverted from
the default timing simply write a “1” to the appropriate
polarity bit to compensate.
DELAY CONTROL
One of the more difficult tasks in designing a scanner
is optimizing the pixel and interface (data output &
OGI) timing for a CCD, CDS and ADC. The
XRD9836 has included a programmable delay func-
tion to help simplify this job.
There are four serial interface registers, DelayA, De-
layB, DelayC and DelayD, used to program various
delays of the pixel timing and Data and OGI bus tim-
ing. Each register is divided into 2 delay parameters.
Each delay parameter is 4 bits wide.
DelayA[7:4] controls the OGI sampling delay. These
bits program the delay of the ADCLK used to sample
the OGI input bus. Delay is added in 1ns increments.
See Figure 12.
DelayA[3:0] controls the ADCDO delay. These bits
are used to program the timing delay added to the
ADCDO data bus updates. Delay is added in 1ns in-
crements. See Figure 11.
DelayB[7:4] controls the amount of delay added to the
leading edge of BSAMP. Delay to the leading edge
will be added in 0.5ns increments. This can help to
position the leading edge of the internal BSAMP away
from the reset pulse of the CCD input. See Figure 11.
DelayB[3:0] controls the amount of delay added to the
trailing edge of BSAMP. Delay to the trailing edge will
be added in 0.5ns increments. This will allow for ad-
justment of the Black Level sampling position by the
internal BSAMP. See Figure 11.
DelayC[7:4] controls the amount of delay added to
the leading edge of VSAMP. Delay will be added in
0.5ns increments. This can help to position the lead-
ing edge of the internal VSAMP to track the video
portion of the CCD input. See Figure 11.
DelayC[3:0] controls the amount of delay added to
the trailing edge of VSAMP. Delay will be added in
0.5ns increments. This will allow for adjustment of the
Video Level sampling position by the internal VSAMP.
See Figure 11.
DelayD[7:4] controls the amount of delay added to
the VSAMP OGI. The internal VSAMP_OGI is used
to transfer the input OGI register data to the PGA and
OFFSET control. Delay is added in 1ns increments.
Please note the falling edge of the internal
VSAMP_OGI must occur before the rising edge of
the OGI sampling clock. See Figure 12.
DelayD[3:0] controls the amount of delay added to
the ADCLK. Delay is added to the internal ADCLK in
0.5ns increments. See Figure 11.
FIGURE 10. CLOCK POLARITY AND DELAYS
Polarity
Delays
Clock
Logic
BSAMP
VSAMP
ADCLK
LCLMP
Polarity
AFE
ADC
OGI
相關PDF資料 |
PDF描述 |
|---|---|
| XRD98L23ACU | IC 8B CCD/CIS SIG PROC 20SSOP |
| XRD98L59AIGTR | IC CCD DIGITIZER 10BIT 28TSSOP |
| XRD98L61AIV-F | IC CCD DIGITIZER 12BIT 48TQFP |
| XRD98L62ACV-F | IC CCD DIGITIZER 12BIT 48TQFP |
| XRD98L63AIV-F | IC CCD DIGITIZER 12BIT 48TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRD9836ACG-F | 功能描述:電信線路管理 IC RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| XRD9836ACGTR-F | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| XRD9853AIV | 制造商:EXAR 制造商全稱:EXAR 功能描述:CCD Image Digitizers with CDS, PGA, and 10-bit A/D |
| XRD9855 | 制造商:EXAR 制造商全稱:EXAR 功能描述:CCD Image Digitizers with CDS, PGA and 10-Bit A/D |
| XRD9855AIV | 制造商:EXAR 制造商全稱:EXAR 功能描述:CCD Image Digitizers with CDS, PGA and 10-Bit A/D |
發布緊急采購，3分鐘左右您將得到回復。