- 您現在的位置：買賣IC網 > PDF目錄1976 > XR20V2170IL40-F (Exar Corporation)IC UART/TXRX I2C/SPI RS232 40QFN PDF資料下載
參數資料
| 型號： | XR20V2170IL40-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 21/49頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART/TXRX I2C/SPI RS232 40QFN |
| 標準包裝： | 490 |
| 特點： | * |
| 通道數： | 1，UART |
| FIFO's： | 64 字節 |
| 規程： | RS232 |
| 電源電壓： | 2.97 V ~ 3.63 V |
| 帶自動流量控制功能： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 40-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 40-QFN 裸露焊盤（6x6） |
| 包裝： | 托盤 |
| 其它名稱： | 1016-1478 XR20V2170IL40-F-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
XR20V2170
28
I2C/SPI UART WITH 64-BYTE FIFO AND RS232 TRANSCEIVER
REV. 1.0.1
MCR[2]: OP1# / TCR and TLR Enable
OP1# is not available as an output pin on the V2170. But it is available for use during Internal Loopback Mode
(MCR[4] = 1). In the Internal Loopback Mode, this bit is used to write the state of the modem RI# interface
signal.
This bit is also used to select between the MSR and TCR registers at address offset 0x6 and the SPR and TLR
registers at address offset 0x7. Table 12 and Table 13 below shows how these registers are accessed.
TABLE 12: REGISTER AT ADDRESS OFFSET 0X6
EFR[4] MCR[2] Register at Address Offset 0x6
0
X
Modem Status Register (MSR)
1
0
Modem Status Register (MSR)
1
Trigger Control Register (TCR)
TABLE 13: REGISTER AT ADDRESS OFFSET 0X7
EFR[4] MCR[2] Register at Address Offset 0x7
0
X
Scratchpad Register (SPR)
1
0
Scratchpad Register (SPR)
1
Trigger Level Register (TLR)
MCR[3]: OP2# Output
OP2# is not available as an output on the V2170 but can be controlled in internal loopback mode.
Logic 0 = OP2# output set HIGH(default).
Logic 1 = OP2# output set LOW.
MCR[4]: Internal Loopback Enable
Logic 0 = Disable loopback mode (default).
Logic 1 = Enable local loopback mode, see loopback section and Figure 13.
MCR[5]: Xon-Any Enable (requires EFR bit-4=1 to write to this bit)
Logic 0 = Disable Xon-Any function (default).
Logic 1 = Enable Xon-Any function. In this mode, any RX character received will resume transmit operation.
The RX character will be loaded into the RX FIFO, unless the RX character is an Xon or Xoff character and
the V2170 is programmed to use the Xon/Xoff flow control.
MCR[6]: Reserved
MCR[7]: Clock Prescaler Select (requires EFR bit-4=1 to write to this bit)
Logic 0 = Divide by one. The input clock from the crystal or external clock is fed directly to the Programmable
Baud Rate Generator without further modification, i.e., divide by one (default).
Logic 1 = Divide by four. The prescaler divides the input clock from the crystal or external clock by four and
feeds it to the Programmable Baud Rate Generator, hence, data rates become one forth.
相關PDF資料 |
PDF描述 |
|---|---|
| XR20V2172IL64-F | IC UART/TXRX I2C/SPI RS232 64QFN |
| XR21V1410IL16TR-F | IC USB UART FIFO FULL SPD 16QFN |
| XR21V1412IL32TR-F | IC USB UART FIFO FULL SPD 32QFN |
| XR21V1414IM48-F | IC UART FIFO USB QUAD 48TQFP |
| XR3178EID-F | IC TXRX RS485 DIFF 3V 8NSOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR20V2170L40-0A-EB | 功能描述:界面開發工具 Supports V2170 40pin QFN,I2C Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR20V2170L40-0B-EB | 功能描述:UART 接口集成電路 Supports V2170 40pin QFN,SPI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR20V2172 | 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL I2C/SPI UART WITH 64-BYTE FIFO AND RS232 TRANSCEIVER |
| XR20V2172_08 | 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL I2C/SPI UART WITH 64-BYTE FIFO AND RS232 TRANSCEIVER |
| XR20V2172IL64 | 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL I2C/SPI UART WITH 64-BYTE FIFO AND RS232 TRANSCEIVER |
發布緊急采購，3分鐘左右您將得到回復。