- 您現在的位置：買賣IC網 > PDF目錄16511 > XR19L400IL40-0B-EB (Exar Corporation)EVAL BOARD FOR XR19L202 40QFN PDF資料下載
參數資料
| 型號： | XR19L400IL40-0B-EB |
| 廠商： | Exar Corporation |
| 文件頁數： | 22/46頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL BOARD FOR XR19L202 40QFN |
| 標準包裝： | 1 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
XR19L400
29
REV. 1.0.3
SINGLE CHANNEL INTEGRATED UART AND RS-485 TRANSCEIVER
4.7
Modem Control Register (MCR) or General Purpose Outputs Control - Read/Write
The MCR register is used for controlling the serial/modem interface signals or general purpose inputs/outputs.
MCR[0]: DTR# Output
DTR# is not available as an output pin on the L400, but it is available for use during internal loopback mode. In
internal loopback mode, this bit is used to write the state of the DSR# interface signal.
Logic 0 = Force DTR# output HIGH (default).
Logic 1 = Force DTR# output LOW.
MCR[1]: RTS# Output
RTS# is not available as an output pin on the L400, but it is available for use during internal loopback mode. In
internal loopback mode, this bit is used to write the state of the CTS# interface signal. If half-duplex mode is
enabled via the Half/Full# pin or in is a modem control output and may be used for automatic hardware flow
control by enabled by EFR bit-6. The RTS# pin can also be used for Auto RS485 Half-Duplex direction control
enabled by FCTR bit-3. If the modem interface is not used, this output may be used as a general purpose
output.
Logic 0 = Force RTS# HIGH (default).
Logic 1 = Force RTS# LOW.
MCR[2]: Reserved
OP1# is not available as an output pin on the L400. But it is available for use during Internal Loopback Mode.
In the Loopback Mode, this bit is used to write the state of the modem RI# interface signal.
MCR[3]: OP2# Output / INT Output Enable
This bit enables or disables the operation of INT, interrupt output. If INT output is not used, OP2# can be used
as a general purpose output. Also, if 16/68# pin selects Motorola bus interface mode, this bit must be set to
logic 0.
Logic 0 = INT (A-B) outputs disabled (three state mode) and OP2# output set HIGH(default).
Logic 1 = INT (A-B) outputs enabled (active mode) and OP2# output set LOW.
MCR[4]: Internal Loopback Enable
Logic 0 = Disable loopback mode (default).
Logic 1 = Enable local loopback mode, see loopback section and Figure 11.
MCR[5]: Xon-Any Enable (requires EFR bit-4=1)
Logic 0 = Disable Xon-Any function (default).
Logic 1 = Enable Xon-Any function. In this mode, any RX character received will resume transmit operation.
The RX character will be loaded into the RX FIFO, unless the RX character is an Xon or Xoff character and
the L400 is programmed to use the Xon/Xoff flow control.
MCR[6]: Reserved
For normal operation, this bit should remain a logic 0.
MCR[7]: Clock Prescaler Select (requires EFR bit-4=1)
Logic 0 = Divide by one. The input clock from the crystal or external clock is fed directly to the Programmable
Baud Rate Generator without further modification, i.e., divide by one (default).
Logic 1 = Divide by four. The prescaler divides the input clock from the crystal or external clock by four and
feeds it to the Programmable Baud Rate Generator, hence, data rates become one forth.
相關PDF資料 |
PDF描述 |
|---|---|
| UVZ2V010MED | CAP ALUM 1UF 350V 20% RADIAL |
| EB63-S1R106FS | CONN EDGEBOARD DUAL 20POS 3A |
| EBM10DRSD-S664 | CONN EDGECARD 20POS DIP .156 SLD |
| M2MXH-3420K | IDC CABLE - MDM34H/MC34F/X |
| 1-5503162-8 | CA SM DUAL 2.5MM/2.5MM 4.58M1 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR19L400IL40-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR19L400IL40TR-F | 功能描述:UART 接口集成電路 Transceiver 1 Tx/1 Rx RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR19L402 | 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL INTEGRATED UART AND RS-485 TRANSCEIVER |
| XR19L402_09 | 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL INTEGRATED UART AND RS-485 TRANSCEIVER |
| XR19L402IL48 | 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL INTEGRATED UART AND RS-485 TRANSCEIVER |
發布緊急采購，3分鐘左右您將得到回復。