參數資料
型號： XR19L212IL48-F
廠商： Exar Corporation
文件頁數： 34/52頁
文件大?。?/td> 0K
描述： IC UART/TXRX RS232 48QFN
標準包裝： 260
特點： *
通道數： 2，DUART
FIFO's： 64 字節
規程： RS232
電源電壓： 3.3 V ~ 5.5 V
帶自動流量控制功能： 是
帶IrDA 編碼器/解碼器： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 48-VFQFN 裸露焊盤
供應商設備封裝： 48-QFN-EP（7x7）
包裝： 托盤
XR19L212
4
TWO CHANNEL INTEGRATED UART AND RS-232 TRANSCEIVER
REV. 1.0.1
MODEM OR SERIAL I/O INTERFACE (EIA-232/RS-232 Voltage Levels)
TXDA
33
O
UART Channel A Transmit Data. The TX signal will be LOW (< 1.5V) during reset or idle (no
data).
RXDA
27
I
UART Channel A Receive Data. The RX data input must idle LOW (< 1.5V). This input has
an internal pull-down resistor and can be left unconnected when not used.
RTSA
24
O
UART Channel A Request-to-Send or general purpose outputs. These outputs must be
asserted prior to using auto RTS flow control, see EFR[6], MCR[1] and IER[6].
CTSA
48
I
UART Channel A Clear-to-Send or general purpose inputs. It can be used for auto CTS
flow control, see EFR[7], MSR[4] and IER[7]. This input has an internal pull-down resistor
and can be left unconnected when not used.
TXDB
22
O
UART Channel B Transmit Data. The TX signal will be LOW (< 1.5V) during reset or idle (no
data).
RXDB
25
I
UART Channel B Receive Data. RXDB will be the input signal to the internal UART when
RXBSEL is LOW. If RXB is used, then RXBSEL should be HIGH. The RX data input must
idle LOW (< 1.5V). This input has an internal pull-down resistor and can be left uncon-
nected when not used.
RTSB
3
O
UART Channel B Request-to-Send or general purpose outputs. These outputs must be
asserted prior to using auto RTS flow control, see EFR[6], MCR[1] and IER[6].
CTSB
2
I
UARTChannel B Clear-to-Send or general purpose inputs. It can be used for auto CTS
flow control, see EFR[7], MSR[4] and IER[7]. This input has an internal pull-down resistor
and can be left unconnected when not used.
SERIAL I/O INTERFACE (CMOS/TTL Voltage Levels)
TXB
9
O
UART Channel B Transmit data. This is the TXB output signal from the UART. This pin can
be used to communicate with an external Infrared or RS-422 transceiver if TXDB is unused.
RXB
8
I
UART Channel B Receive data. This is the RXB input signal to the UART. If RXDB is not
used (RXBSEL is HIGH), then this pin can be used to communicate with an external Infra-
red or RS-422 transceiver. If RXDB is used (RXBSEL is LOW), this pin should be left open.
ANCILLARY SIGNALS (CMOS/TTL Voltage Levels)
XTAL1
13
I
Crystal or external clock input. This input is not 5V tolerant.
XTAL2
14
O
Crystal or buffered clock output. This output may be use to drive a clock buffer which can
drive other device(s).
PwrSave
12
I
Power-Save (active high). This feature isolates the L212’s data bus interface from the host
preventing other bus activities that cause higher power drain during sleep mode. See Sleep
Mode with Auto Wake-up and Power-Save Feature section for details.
ACP
20
I
Autosleep for Charge Pump (active HIGH). When this pin is HIGH, the charge pump is shut
off if the L212 is already in partial sleep mode, i.e. the crystal oscillator is stopped.
Pin Descriptions
NAME
48-QFN
PIN#
TYPE
DESCRIPTION
相關PDF資料
PDF描述
XR19L220IL40-F IC UART/TXRX RS232 40QFN
XR19L222IL64-F IC UART/TXRX RS232 64QFN
XR19L400IL40-F IC UART/TXRX RS485 40QFN
XR19L402IL48-F IC UART/TXRX RS485 48QFN
XR20M1170IL24TR-F IC UART FIFO I2C/SPI 64B 24QFN
相關代理商/技術參數
參數描述
XR19L212IL48TR-F 制造商:Exar Corporation 功能描述:UART 2-CH 64Byte FIFO 5V 48-Pin QFN EP T/R 制造商:Exar Corporation 功能描述:XR19L212IL48TR-F
XR19L220 制造商:EXAR 制造商全稱:EXAR 功能描述:SINGLE CHANNEL INTEGRATED UART AND RS-232 TRANSCEIVER
XR19L220_07 制造商:EXAR 制造商全稱:EXAR 功能描述:SINGLE CHANNEL INTEGRATED UART AND RS-232 TRANSCEIVER
XR19L220IL40 制造商:EXAR 制造商全稱:EXAR 功能描述:SINGLE CHANNEL INTEGRATED UART AND RS-232 TRANSCEIVER
XR19L220IL40-0A-EB 功能描述:界面開發工具 Supports L220 40 pin QFN, ISA Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*