REV. 1.0.2 LSR[1]: Receiver Overrun Flag
參數資料
型號： XR17V258IV-0A-EVB
廠商： Exar Corporation
文件頁數： 48/69頁
文件大?。?/td> 0K
描述： EVAL BOARD FOR XR17V258 144LQFP
標準包裝： 1
系列： *
XR17V258
52
66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
REV. 1.0.2
LSR[1]: Receiver Overrun Flag
Logic 0 = No overrun error (default).
Logic 1 = Overrun error. A data overrun error condition occurred in the receive shift register. This happens
when additional data arrives while the FIFO is full. In this case the previous data in the receive shift register
is overwritten. Note that under this condition the data byte in the receive shift register is not transferred into
the FIFO, therefore the data in the FIFO is not corrupted by the error.
LSR[0]: Receive Data Ready Indicator
Logic 0 = No data in receive holding register or FIFO (default).
Logic 1 = Data has been received and is saved in the receive holding register or FIFO.
5.10
Modem Status Register (MSR) - Read Only
This register provides the current state of the modem interface signals, or other peripheral device that the
UART is connected. Lower four bits of this register are used to indicate the changed information. These bits
are set to a logic 1 whenever a signal from the modem changes state. These bits may be used as general
purpose inputs/outputs when they are not used with modem signals.
MSR[7]: CD Input Status
Normally this bit is the complement of the CD# input. In the loopback mode this bit is equivalent to bit [3] in the
MCR register. The CD# input may be used as a general purpose input when the modem interface is not used.
MSR[6]: RI Input Status
Normally this bit is the complement of the RI# input. In the loopback mode this bit is equivalent to bit [2] in the
MCR register. The RI# input may be used as a general purpose input when the modem interface is not used.
MSR[5]: DSR Input Status
DSR# pin may function as automatic hardware flow control signal input if it is enabled and selected by Auto
CTS/DSR bit (EFR bit [6]=1) and RTS/DTR flow control select bit (MCR bit [2]=1). Auto CTS/DSR flow control
allows starting and stopping of local data transmissions based on the modem DSR# signal. A HIGH on the
DSR# pin will stop UART transmitter as soon as the current character has finished transmission, and a LOW
will resume data transmission. Normally MSR bit [5] is the complement of the DSR# input. However in the
loopback mode, this bit is equivalent to the DTR# bit in the MCR register. The DSR# input may be used as a
general purpose input when the modem interface is not used.
MSR[4]: CTS Input Status
CTS# pin may function as automatic hardware flow control signal input if it is enabled and selected by Auto
CTS/DSR bit (EFR bit [6]=1) and RTS/DTR flow control select bit (MCR bit [2]=0). Auto CTS/DSR flow control
allows starting and stopping of local data transmissions based on the modem CTS# signal. A HIGH on the
CTS# pin will stop UART transmitter as soon as the current character has finished transmission, and a LOW
will resume data transmission. Normally MSR bit [4] is the complement of the CTS# input. However in the
loopback mode, this bit is equivalent to the RTS# bit in the MCR register. The CTS# input may be used as a
general purpose input when the modem interface is not used.
MSR[3]: Delta CD# Input Flag
Logic 0 = No change on CD# input (default).
Logic 1 = Indicates that the CD# input has changed state since the last time it was monitored. A modem
status interrupt will be generated if MSR interrupt is enabled (IER bit [3]).
MSR[2]: Delta RI# Input Flag
Logic 0 = No change on RI# input (default).
Logic 1 = The RI# input has changed from a LOW to a HIGH, ending of the ringing signal. A modem status
interrupt will be generated if MSR interrupt is enabled (IER bit [3]).
相關PDF資料
PDF描述
GCC10DRYN-S734 CONN EDGECARD 20POS DIP .100 SLD
VI-B1Y-EV CONVERTER MOD DC/DC 3.3V 99W
155880-000 SOLDER SLEEVE 11MM DIA SHIELD
VI-2VR-EX CONVERTER MOD DC/DC 7.5V 75W
VI-2VP-EX CONVERTER MOD DC/DC 13.8V 75W
相關代理商/技術參數
參數描述
XR17V258IVF 制造商:Exar Corporation 功能描述:
XR17V258IV-F 功能描述:UART 接口集成電路 66MHz Octal PCI UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR17V258IVTR-F 功能描述:UART 接口集成電路 66MHz Octal PCI UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR17V352 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE DUAL PCI EXPRESS UART
XR17V352IB-0A-EVB 功能描述:界面開發工具 Eval Board for XR17V352IB Series RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*