- 您現在的位置：買賣IC網 > PDF目錄16524 > XR16V2552IL-0B-EB (Exar Corporation)EVAL BOARD FOR V2552 32QFN PDF資料下載
參數資料
| 型號： | XR16V2552IL-0B-EB |
| 廠商： | Exar Corporation |
| 文件頁數： | 42/46頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL BOARD FOR V2552 32QFN |
| 標準包裝： | 1 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁當前第42頁第43頁第44頁第45頁第46頁
XR16V2552
5
REV. 1.0.3
HIGH PERFORMANCE DUART WITH 16-BYTE FIFO
Pin type: I=Input, O=Output, I/O= Input/output, OD=Output Open Drain.
CTSB#
17
28
I
UART channel B Clear-to-Send (active low) or general purpose input.
It can be used for auto CTS flow control, see EFR[7], and IER[7]. This
input should be connected to VCC when not used.
DTRB#
-
27
O
UART channel B Data-Terminal-Ready (active low) or general purpose
output. If this pin is not used, leave it unconnected.
DSRB#
-
29
I
UART channel B Data-Set-Ready (active low) or general purpose input.
This input should be connected to VCC when not used. This input has
no effect on the UART.
CDB#
-
30
I
UART channel B Carrier-Detect (active low) or general purpose input.
This input should be connected to VCC when not used. This input has
no effect on the UART.
RIB#
-
31
I
UART channel B Ring-Indicator (active low) or general purpose input.
This input should be connected to VCC when not used. This input has
no effect on the UART.
MFB#
-
19
O
Multi-Function Output Channel B. This output pin can function as the
OP2B#, BAUDOUTB#, or RXRDYB# pin. One of these output signal
functions can be selected by the user programmable bits 1-2 of the
Alternate Function Register (AFR). These signal functions are
described as follows:
1) OP2B# - When OP2B# (active low) is selected, the MF# pin is LOW
when MCR bit-3 is set HIGH (see MCR bit-3). MCR bit-3 defaults to a
logic 0 condition after a reset or power-up.
2) BAUDOUTB# - When BAUDOUTB# function is selected, the Baud
rate clock output is available at this pin.
3) RXRDYB# - RXRDYB# (active low) is intended for monitoring block
data transfers. See
Table 2 for more details.
ANCILLARY SIGNALS
XTAL1
4
11
I
Crystal or external clock input.
XTAL2
5
13
O
Crystal or buffered clock output.
RESET
12
21
I
Reset (active high) - A longer than 40 ns HIGH pulse on this pin will
reset the internal registers and all outputs. The UART transmitter out-
put will be held HIGH, the receiver input will be ignored and outputs are
reset during reset period (see Table 15).
VCC
26
44, 33
Pwr
2.25 to 3.6V power supply. All input pins are 5V tolerant.
GND
20
22, 12
Pwr
Power supply common, ground.
GND
Center Pad
N/A
Pwr
The center pad on the backside of the 32-QFN package is metallic and
should be connected to GND on the PCB. The thermal pad size on the
PCB should be the approximate size of this center pad and should be
solder mask defined. The solder mask opening should be at least
0.0025" inwards from the edge of the PCB thermal pad.
NC
18, 19
-
No Connect.
Pin Description
NAME
32-QFN
PIN #
44-PLCC
PIN #
TYPE
DESCRIPTION
相關PDF資料 |
PDF描述 |
|---|---|
| UUR1H470MNL1GS | CAP ALUM 47UF 50V 20% SMD |
| UUX1J220MNL1GS | CAP ALUM 22UF 63V 20% SMD |
| A1DXH-4436G | IDC CABLE - AKR44H/AE44G/X |
| GEM22DTAI | CONN EDGECARD 44POS R/A .156 SLD |
| RMM06DRAI | CONN EDGECARD 12POS R/A .156 SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16V2552IL32 | 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 16-BYTE FIFO |
| XR16V2552IL-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16V2650 | 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 32-BYTE FIFO |
| XR16V2650_07 | 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 32-BYTE FIFO |
| XR16V2650IL | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。