- 您現在的位置：買賣IC網 > PDF目錄16524 > XR16V2552IL-0B-EB (Exar Corporation)EVAL BOARD FOR V2552 32QFN PDF資料下載
參數資料
| 型號： | XR16V2552IL-0B-EB |
| 廠商： | Exar Corporation |
| 文件頁數： | 20/46頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL BOARD FOR V2552 32QFN |
| 標準包裝： | 1 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
XR16V2552
27
REV. 1.0.3
HIGH PERFORMANCE DUART WITH 16-BYTE FIFO
FCR[1]: RX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
Logic 0 = No receive FIFO reset (default).
Logic 1 = Reset the receive FIFO pointers (the receive shift register is not cleared or altered). This bit will
return to a logic 0 after resetting the FIFO.
FCR[2]: TX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
Logic 0 = No transmit FIFO reset (default).
Logic 1 = Reset the transmit FIFO pointers (the transmit shift register is not cleared or altered). This bit will
return to a logic 0 after resetting the FIFO.
FCR[3]: DMA Mode Select
Controls the behavior of the TXRDY# and RXRDY# pins. See DMA operation section for details.
Logic 0 = Normal Operation (default).
Logic 1 = DMA Mode.
FCR[5:4]: Transmit FIFO Trigger Select (requires EFR bit-4 = 1)
(logic 0 = default, TX trigger level = 1)
These 2 bits set the trigger level for the transmit FIFO. The UART will issue a transmit interrupt when the
number of characters in the FIFO falls below the selected trigger level, or when it gets empty in case that the
FIFO did not get filled over the trigger level on last re-load. Table 11 below shows the selections. EFR bit-4
must be set to ‘1’ before these bits can be accessed.
FCR[7:6]: Receive FIFO Trigger Select
(logic 0 = default, RX trigger level =1)
These 2 bits are used to set the trigger level for the receive FIFO. The UART will issue a receive interrupt when
the number of the characters in the FIFO crosses the trigger level. Table 11 shows the complete selections.
TABLE 11: TRANSMIT AND RECEIVE FIFO TRIGGER TABLE AND LEVEL SELECTION
FCR BIT-7
FCR BIT-6
FCR BIT-5
FCR BIT-4
RECEIVE
TRIGGER LEVEL
TRANSMIT
TRIGGER LEVEL
COMPATIBILITY
0
1
0
1
0
1
0
1
0
1
0
1
4
8
14
1
4
8
14
16C550,
16C2550,
16C2552,
16C554,
16C580
4.6
Line Control Register (LCR) - Read/Write
The Line Control Register is used to specify the asynchronous data communication format. The word or
character length, the number of stop bits, and the parity are selected by writing the appropriate bits in this
register.
相關PDF資料 |
PDF描述 |
|---|---|
| UUR1H470MNL1GS | CAP ALUM 47UF 50V 20% SMD |
| UUX1J220MNL1GS | CAP ALUM 22UF 63V 20% SMD |
| A1DXH-4436G | IDC CABLE - AKR44H/AE44G/X |
| GEM22DTAI | CONN EDGECARD 44POS R/A .156 SLD |
| RMM06DRAI | CONN EDGECARD 12POS R/A .156 SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16V2552IL32 | 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 16-BYTE FIFO |
| XR16V2552IL-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16V2650 | 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 32-BYTE FIFO |
| XR16V2650_07 | 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 32-BYTE FIFO |
| XR16V2650IL | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。