參數資料
型號： XR16L784IV-F
廠商： Exar Corporation
文件頁數： 7/51頁
文件大?。?/td> 0K
描述： IC UART 8B 3.3V QUAD 64LQFP
標準包裝： 160
特點： *
通道數： 4，QUART
FIFO's： 64 字節
規程： RS485
電源電壓： 2.97 V ~ 5.5 V
帶自動流量控制功能： 是
帶IrDA 編碼器/解碼器： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
安裝類型： 表面貼裝
封裝/外殼： 64-LQFP
供應商設備封裝： 64-LQFP（10x10）
包裝： 托盤
其它名稱： 1016-1282
XR16L784
15
REV. 1.2.3
HIGH PERFORMANCE 2.97V TO 5.5V QUAD UART
2.13
Auto RS485 Half-duplex Control
The auto RS485 half-duplex direction control changes the behavior of the transmitter when enabled by FCTR
bit-5. It asserts RTS# or DTR# (LOW) after a specified delay indicated in MSR[7:4] following the last stop bit of
the last character that has been transmitted. This helps in turning around the transceiver to receive the remote
station’s response. The delay optimizes the time needed for the last transmission to reach the farthest station
on a long cable network before switching off the line driver. This delay prevents undesirable line signal
disturbance that causes signal degradation. When the host is ready to transmit next polling data packet again,
it only has to load data bytes to the transmit FIFO. The transmitter automatically de-asserts RTS# or DTR#
output (HIGH) prior to sending the data. The auto RS485 half-duplex direction control also changes the
transmitter empty interrupt to TSR empty instead of THR empty.
2.14
Infrared Mode
Each UART in the 784 includes the infrared encoder and decoder compatible to the IrDA (Infrared Data
Association) version 1.0. The input pin ENIR conveniently activates all 8 UART channels to start up in the
infrared mode. Note that the ENIR pin is sampled when the RST# input is de-asserted. This global control pin
enables the MCR bit-6 function in every UART channel register. After power up or a reset, the software can
overwrite MCR bit-6 if so desired. ENIR and MCR bit-6 also disable the receiver while the transmitter is
sending data. This prevents echoed data from reaching the receiver. The global activation ENIR pin prevents
the infrared emitter from turning on and drawing large amount of current while the system is starting up. When
the infrared feature is enabled, the transmit data outputs, TX[3:0], would idle at logic zero level. Likewise, the
RX [3:0] inputs assume an idle level of logic zero.
The infrared encoder sends out a 3/16 of a bit wide HIGH-pulse for each “0” bit in the transmit data stream.
This signal encoding reduces the on-time of the infrared LED, hence reduces the power consumption. See
The infrared decoder receives the input pulse from the infrared sensing diode on RX pin. Each time it senses a
light pulse, it returns a logic zero to the data bit stream. The decoder also accepts (when FCTR bit-4 = 1) an
inverted IR-encoded input signal. This option supports active low instead of normal active high pulse from
some infrared modules on the market.
相關PDF資料
PDF描述
XR16L788IQ-F IC UART 64B 3.3V OCTAL 100QFP
XR16M2550IL32-F IC UART FIFO 16B 1.8V DUAL 32QFN
XR16M2551IL32-F IC UART FIFO 16B DUAL 32QFN
XR16M2650IM48-F IC UART FIFO 32B DUAL 48TQFP
XR16M2651IM48-F IC UART FIFO 32B DUAL 48TQFP
相關代理商/技術參數
參數描述
XR16L784IVTR-F 功能描述:UART 接口集成電路 PCI BUS QUAD UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L788 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE OCTAL UART
XR16L788_05 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE 2.97V TO 5.5V OCTAL UART
XR16L788_08 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE 2.97V TO 5.5V OCTAL UART
XR16L788CQ 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE 2.97V TO 5.5V OCTAL UART
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*