- 您現在的位置：買賣IC網 > PDF目錄376454 > XR16L2752IJ (EXAR CORP) 2.25V TO 5.5V DUART WITH 64-BYTE FIFO PDF資料下載
參數資料
| 型號： | XR16L2752IJ |
| 廠商： | EXAR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 2.25V TO 5.5V DUART WITH 64-BYTE FIFO |
| 中文描述： | 2 CHANNEL(S), 6.25M bps, SERIAL COMM CONTROLLER, PQCC44 |
| 封裝： | PLASTIC, LCC-44 |
| 文件頁數： | 8/49頁 |
| 文件大?。?/td> | 619K |
| 代理商： | XR16L2752IJ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
XR16L2752
2.25V TO 5.5V DUART WITH 64-BYTE FIFO
xr
REV. 1.2.0
8
2.6
Each UART channel in the 2752 has a set of enhanced registers for control, monitoring and data loading and
unloading. The configuration register set is compatible to those already available in the standard single
16C550 and dual ST16C2550. These registers function as data holding registers (THR/RHR), interrupt status
and control registers (ISR/IER), a FIFO control register (FCR), receive line status and control registers (LSR/
LCR), modem status and control registers (MSR/MCR), programmable data rate (clock) divisor registers (DLL/
DLM), and a user accessible Scratchpad Register (SPR).
Beyond the general 16C2550 features and capabilities, the 2752 offers enhanced feature registers (AFR,
EMSR, FLVL, EFR, Xon/Xoff 1, Xon/Xoff 2, FCTR, TRG, FC) that provide automatic RTS and CTS hardware
flow control, Xon/Xoff software flow control, automatic RS-485 half-duplex direction output enable/disable,
FIFO trigger level control, FIFO level counters, and simultaneous writes to both channels. All the register
functions are discussed in full detail later in
“Section 3.0, UART INTERNAL REGISTERS” on page 20
.
2.7
Simultaneous Write to Channel A and B
During a write mode cycle, the setting of Alternate Function Register (AFR) bit-0 to a logic 1 will override the
CHSEL selection and allows a simultaneous write to both UART channel sections. This functional capability
allow the registers in both UART channels to be modified concurrently, saving individual channel initialization
time. Caution should be considered, however, when using this capability. Any in-process serial data transfer
may be disrupted by changing an active channel’s mode.
2.8
DMA Mode
The device does not support direct memory access. The DMA Mode (a legacy term) in this document doesn’t
mean “direct memory access” but refers to data block transfer operation. The DMA mode affects the state of
the RXRDY# A/B (MF# A/B becomes RXRDY# A/B output when AFR[2:1] = ‘10’) and TXRDY# A/B output
pins. The transmit and receive FIFO trigger levels provide additional flexibility to the user for block mode
operation. The LSR bits 5-6 provide an indication when the transmitter is empty or has an empty location(s) for
more data. The user can optionally operate the transmit and receive FIFO in the DMA mode (FCR bit-3=1).
When the transmit and receive FIFO are enabled and the DMA mode is disabled (FCR bit-3 = 0), the 2752 is
placed in single-character mode for data transmit or receive operation. When DMA mode is enabled (FCR bit-
3 = 1), the user takes advantage of block mode operation by loading or unloading the FIFO in a block
sequence determined by the programmed trigger level. In this mode, the 2752 sets the TXRDY# pin when the
transmit FIFO becomes full, and sets the RXRDY# pin when the receive FIFO becomes empty. The following
table shows their behavior. Also see
Figures 18
through
23
.
Channel A and B Internal Registers
T
ABLE
1: C
HANNEL
A
AND
B S
ELECT
CHSEL
F
UNCTION
1
X
UART de-selected
0
1
Channel A selected
0
0
Channel B selected
T
ABLE
2: TXRDY#
AND
RXRDY# O
UTPUTS
IN
FIFO
AND
DMA M
ODE
P
INS
FCR
BIT
-0=0
(FIFO D
ISABLED
)
FCR B
IT
-0=1 (FIFO E
NABLED
)
FCR Bit-3 = 0
(DMA Mode Disabled)
FCR Bit-3 = 1
(DMA Mode Enabled)
RXRDY# A/B LOW = 1 byte.
HIGH = no data.
LOW = at least 1 byte in FIFO.
HIGH = FIFO empty.
HIGH to LOW transition when FIFO reaches the
trigger level, or time-out occurs.
LOW to HIGH transition when FIFO empties.
TXRDY# A/B LOW = THR empty.
HIGH = byte in THR.
LOW = FIFO empty.
HIGH = at least 1 byte in FIFO.
LOW = FIFO has at least 1 empty location.
HIGH = FIFO is full.
相關PDF資料 |
PDF描述 |
|---|---|
| XR16L580 | SMALLEST 2.25V TO 5.5V UART WITH 16-BYTE FIFO AND POWERSAVE |
| XR16L580IL | SMALLEST 2.25V TO 5.5V UART WITH 16-BYTE FIFO AND POWERSAVE |
| XR16L580IM | SMALLEST 2.25V TO 5.5V UART WITH 16-BYTE FIFO AND POWERSAVE |
| XR16L651 | 2.5V, 3.3V and 5V Low Power UART with 32-Byte FIFO(2.5V, 3.3V和5V 低功耗通用異步接收器/發送器（帶32字節先進先出）) |
| XR16L784 | HIGH PERFORMANCE 2.97V TO 5.5V QUAD UART |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16L2752IJ-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16L2752IJTR-F | 制造商:Exar Corporation 功能描述:XR16L2752 Series 6.25 Mbps 5.5 V Dual UART With 64-Byte FIFO - PLCC-44 |
| XR16L570 | 制造商:EXAR 制造商全稱:EXAR 功能描述:SMALLEST 1.62V TO 5.5V UART WITH 16-BYTE FIFO AND POWERSAVE |
| XR16L570_07 | 制造商:EXAR 制造商全稱:EXAR 功能描述:SMALLEST 1.62V TO 5.5V UART WITH 16-BYTE FIFO AND POWERSAVE |
| XR16L570IL24 | 功能描述:UART 接口集成電路 UART w/ POWER SAVE RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。