參數資料
型號： XR16C2852IJ
廠商： EXAR CORP
元件分類： 微控制器/微處理器
英文描述： 3.3V AND 5V DUART WITH 128-BYTE FIFO
中文描述： 2 CHANNEL(S), 3.125M bps, SERIAL COMM CONTROLLER, PQCC44
封裝： PLASTIC, LCC-44
文件頁數： 3/42頁
文件大?。?/td> 574K
代理商： XR16C2852IJ
XR16C2852
REV. 2.0.0
3.3V AND 5V DUART WITH 128-BYTE FIFO
á
3
PIN DESCRIPTIONS
N
AME
44-PLCC
P
IN
#
T
YPE
D
ESCRIPTION
DATA BUS INTERFACE
A2
A1
A0
10
14
15
I
Address data lines [2:0]. These 3 address lines select one of the internal registers in
UART channel A/B during a data bus transaction.
D7
D6
D5
D4
D3
D2
D1
D0
9
8
7
6
5
4
3
2
I/O
Data bus lines [7:0] (bidirectional).
IOR#
24
I
Input/Output Read Strobe (active low). The falling edge instigates an internal read
cycle and retrieves the data byte from an internal register pointed to by the address
lines [A2:A0]. The data byte is placed on the data bus to allow the host processor to
read it on the rising edge.
IOW#
20
I
Input/Output Write Strobe (active low). The falling edge instigates an internal write
cycle and the rising edge transfers the data byte on the data bus to an internal regis-
ter pointed by the address lines.
CS#
18
I
UART chip select (active low). This function selects channel A or B in accordance
with the logical state of the CHSEL pin. This allows data to be transferred between
the user CPU and the 2852.
CHSEL
16
I
Channel Select - UART channel A or B is selected by the logical state of this pin when
the CS# pin is a logic 0. A logic 0 on the CHSEL selects the UART channel B while a
logic 1 selects UART channel A. Normally, CHSEL could just be an address line from
the user CPU such as A4. Bit-0 of the Alternate Function Register (AFR) can tempo-
rarily override CHSEL function, allowing the user to write to both channel register
simultaneously with one write cycle when CS# is low. It is especially useful during the
initialization routine.
INTA
INTB
34
17
O
UART channel A or B Interrupt output (active high). A logic high indicates channel A
or B is requesting for service. For more details, see Figures 18- 23.
TXRDYA#
TXRDYB#
1
32
O
UART channel A or B Transmitter Ready (active low). The output provides
the TX FIFO/THR status for transmit channel A or B. See Table 2 on page 7.
MODEM OR SERIAL I/O INTERFACE
MFA#
35
O
Multi-Function Output Channel A. This output pin can function as the OP2A#, BAUD-
OUTA#, or RXRDYA# pin. One of these output signal functions can be selected by
the user programmable bits 1-2 of the Alternate Function Register (AFR). These sig-
nal functions are described as follows:
1) OP2A# - When OP2A# (active low) is selected, the MF# pin is a logic 0 when MCR
bit-3 is set to a logic 1 (see MCR bit-3). MCR bit-3 defaults to a logic 1 condition after
a reset or power-up.
2) BAUDOUTA# - When BAUDOUTA# function is selected, the 16X Baud rate clock
output is available at this pin.
3) RXRDYA# - RXRDYA# (active low) is intended for monitoring DMA data transfers.
See Table 2 on page 7 for more details.
相關PDF資料
PDF描述
XR16C850CJ UART with 128-byte FIFO’s FIFO Counters and Half-duplex Control
XR16C850CM UART with 128-byte FIFO’s FIFO Counters and Half-duplex Control
XR16C850CP UART with 128-byte FIFO’s FIFO Counters and Half-duplex Control
XR16C850CQ UART with 128-byte FIFO’s FIFO Counters and Half-duplex Control
XR16C850 UART with 128-byte FIFO’s FIFO Counters and Half-duplex Control
相關代理商/技術參數
參數描述
XR16C2852IJ-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16C2852IJTR-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR-16C450CJ 制造商:未知廠家 制造商全稱:未知廠家 功能描述:UART
XR-16C450CP 制造商:未知廠家 制造商全稱:未知廠家 功能描述:UART
XR-16C452CJ 制造商:未知廠家 制造商全稱:未知廠家 功能描述:UART
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*