- 您現在的位置：買賣IC網 > Datasheet目錄58 > XIB-E (Digi International/Maxstream)BOARD INTERFACE ETHERNET Datasheet資料下載
參數資料
| 型號： | XIB-E |
| 廠商： | Digi International/Maxstream |
| 文件頁數： | 26/64頁 |
| 文件大小： | 1858K |
| 描述： | BOARD INTERFACE ETHERNET |
| 標準包裝： | 1 |
| 附件類型： | 接口板 |
| 適用于相關產品： | XStream 和 Xcite 收音機 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
XStream"燨EM燫F燤odule?燩roduct燤anual爒5.x00燵2006.02.24]?/DIV>
HT (Time before Wake-up Initializer) Command
<Sleep (Low Power)> If any modules within
range are running in a Cyclic Sleep setting, a
wake-up initializer must be used by the
transmitting module for sleeping modules to
remain awake [refer to the LH ( Wake-up
Initializer Timer ) Command]. When a receiving
module in Cyclic Sleep wakes, it must detect the
wake-up initializer in order to remain awake and
receive data. The value of HT Parameter tells the
transmitter, After a period of inactivity (no
transmitting or receiving) lasting HT amount of time, send a long wake-up initializer . HT
Parameter should be set to match the inactivity timeout [specified by ST (Time before Sleep)
Command] used by the receiver(s).
AT Command: ATHT
Binary Command: 0x03 (3 decimal)
Parameter Range: 0 0xFFFF
[x 100 milliseconds]
Default Parameter Value: 0xFFFF (means that
long wake-up initializer will not be sent)
Number of bytes returned: 2
Related Commands: LH (Wake-up Initializer
Timer), SM (Sleep Mode), ST (Time before
Sleep)
From the receiving module perspective, after HT time elapses and the inactivity timeout (ST
command) is met, the receiver goes into cyclic sleep. In cyclic sleep, the receiver wakes once per
sleep interval to check for a wake-up initializer. When a wake-up initializer is detected, the
module will stay awake to receive data. The wake-up initializer must be longer than the cyclic
sleep interval to ensure that sleeping modules detect incoming data. When HT time elapses, the
transmitter then knows that it needs to send a long Wake-up Initializer for all receivers to be able
to remain awake and receive the next transmission. Matching HT to the time specified by ST on
the receiving module guarantees that all receivers will detect the next transmission.
ID (Modem VID) Command
AT Command: ATID
Binary Command: 0x27 (39 decimal)
<Networking & Security> Set/Read the VID
(Vendor Identification Number). Only modules
with matching VIDs can communicate with each
other. Modules with non-matching VIDs will not
receive unintended data transmission.
Parameter Range (user-settable):
0x10 - 0x7FFFF
(Factory-set and read-only) :
0x8000 0xFFFF
Number of bytes returned: 2
Minimum Firmware Version Required: 4.2B
牋牘?006燤axStream,營nc.燙onfidential燼nd燩roprietary?/DIV>
26?/DIV>
(previous firmware versions did not support
user-settable IDs.)
IU (DI2, DI3 Update Timer) Command
AT Command: ATIU
Binary Command: 0x3B (59 decimal)
Parameter Range: 0 - 0xFFFF [x 100 ms]
Default Parameter Value: 0x0A (10 decimal)
Number of bytes returned: 2
Related Commands: BK (Serial Break Passing),
BO (Serial Break Timeout), CO (DO3 Timeout),
DR (Disconnect), RT (DI2 Configuration), TO
(DO2 Timeout)
Minimum Firmware Version Required: 4.30
<Serial Interfacing> Set/Read the interval at
which the status of DI2, DI3 and Break is
transmitted. Additionally, status is transmitted
whenever there is a transition. A setting of 0
disables periodic update. DI2 or DI3 passing
must be enabled for the update to take place.
相關PDF資料 |
PDF描述 |
|---|---|
| XIB-R | BOARD INTERFACE RS232/485 |
| ZMN2400HPDB | BOARD ROUTER DEV ZIGBEE 100MW |
| ZMN24HPDK-B | KIT DEV W/ZIGBEE ZMN2400HP |
| ZNI1000TC | IC TEMP SENSOR NI1000 SOT23-3 |
| 02110102-000 | SNSR TILT RATIO 60DEG 500MA FLNG |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XIB-R | 功能描述:界面模塊 RS-232/485 interface 24XStream 9XCite RoHS:否 制造商:4D Systems 產品:Serial Converters 通道/端口數量: 數據速率: 接口類型:USB, UART 工作電源電壓:3.3 V, 5 V 最大工作溫度: |
| XIB-U | 功能描述:界面模塊 USB interface board 24XStream 9XCite RoHS:否 制造商:4D Systems 產品:Serial Converters 通道/端口數量: 數據速率: 接口類型:USB, UART 工作電源電壓:3.3 V, 5 V 最大工作溫度: |
| XIC25040 | 制造商:XIC 功能描述:25040 24HR '6 |
| XILINXPWR-079 | 功能描述:電源管理IC開發工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| XILINXPWR-080 | 功能描述:電源管理IC開發工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
發布緊急采購，3分鐘左右您將得到回復。