參數資料
型號： XIB-E
廠商： Digi International/Maxstream
文件頁數： 16/64頁
文件大?。?/td> 1858K
描述： BOARD INTERFACE ETHERNET
標準包裝： 1
附件類型： 接口板
適用于相關產品： XStream 和 Xcite 收音機
XStream"燨EM燫F燤odule?燩roduct燤anual爒5.x00燵2006.02.24]?/DIV>
2.2.5. Command Mode
To modify or read module parameters, the module must first enter into Command Mode (a state
in which incoming characters are interpreted as commands). Two command types are supported:
"   AT Commands
"   Binary Commands
AT Commands
To Enter AT Command Mode:
1.   Send the 3-character command sequence +++ and observe guard times before and after
the command characters. [Refer to the Default AT Command Mode Sequence below.] The
Terminal tab (or other serial communications software) of the X-CTU Software can be used
to enter the sequence.
 
[OR]
2.   Assert (low) the
 pin and either turn the power going to the module off and back on.
(If using a MaxStream XIB-R Interface Board, the same result can be achieved by keeping
the configuration switch pressed while turning off, then on again the power supplying the
module assembly (module assembly = module mounted to an interface board))
Default AT Command Mode Sequence (for transitioning to Command Mode):
"   No characters sent for one second [BT (Guard Time Before) parameter = 0x0A]
"   Input three plus characters (+++) within one second [CC (Command Sequence Character)
Command = 0x2B-0]
"   No characters sent for one second [AT (Guard Time After) parameter = 0x0A]
To Send AT Commands:
Send AT commands and parameters using the syntax shown below.
Figure?10. Syntax爁or爏ending燗T燙ommands?/DIV>
 
 
 
 
The preceding example would change the module Destination Address to 0x1F. For modified
parameter values to persist in the module registry, changes must be saved to non-volatile
memory using WR (Write) Command. Otherwise, parameters are restored to previously saved
values after the module is powered off and then on again.
NOTE: To read the current value of a module parameter, leave the parameter field blank. For
example, the following command will return the current destination address: ATDT
System Response. When a command is sent to the module, the module will parse and execute
the command. Upon successful execution of a command, the module returns an OK message. If
execution of a command results in an error, the module returns an ERROR message.
To Exit AT Command Mode:
1.   Send ATCN (Exit Command Mode) Command.
 
[OR]
2.   If no valid AT Commands are received within the time specified by CT (Command Mode
Timeout) Command, the Module automatically returns to Idle Mode.
For an example that illustrates programming the module using AT Commands, refer to the
Module Configuration chapter [p18].
牋牘?006燤axStream,營nc.燙onfidential燼nd燩roprietary?/DIV>
16?/DIV>
相關PDF資料
PDF描述
XIB-R BOARD INTERFACE RS232/485
ZMN2400HPDB BOARD ROUTER DEV ZIGBEE 100MW
ZMN24HPDK-B KIT DEV W/ZIGBEE ZMN2400HP
ZNI1000TC IC TEMP SENSOR NI1000 SOT23-3
02110102-000 SNSR TILT RATIO 60DEG 500MA FLNG
相關代理商/技術參數
參數描述
XIB-R 功能描述:界面模塊 RS-232/485 interface 24XStream 9XCite RoHS:否 制造商:4D Systems 產品:Serial Converters 通道/端口數量: 數據速率: 接口類型:USB, UART 工作電源電壓:3.3 V, 5 V 最大工作溫度:
XIB-U 功能描述:界面模塊 USB interface board 24XStream 9XCite RoHS:否 制造商:4D Systems 產品:Serial Converters 通道/端口數量: 數據速率: 接口類型:USB, UART 工作電源電壓:3.3 V, 5 V 最大工作溫度:
XIC25040 制造商:XIC 功能描述:25040 24HR '6
XILINXPWR-079 功能描述:電源管理IC開發工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
XILINXPWR-080 功能描述:電源管理IC開發工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*