- 您現在的位置：買賣IC網 > PDF目錄9415 > X9448WV24I-2.7 (Intersil)IC DUAL PROG COMP 10K 24TSSOP PDF資料下載
參數資料
| 型號： | X9448WV24I-2.7 |
| 廠商： | Intersil |
| 文件頁數： | 12/19頁 |
| 文件大小： | 0K |
| 描述： | IC DUAL PROG COMP 10K 24TSSOP |
| 標準包裝： | 75 |
| 系列： | XDCP™ |
| 接片： | 64 |
| 電阻（歐姆）： | 10k |
| 電路數： | 2 |
| 溫度系數： | 標準值 ±300 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | I²C（設備位址） |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 24-TSSOP |
| 包裝： | 管件 |
2
FN8201.0
April 18, 2005
PIN DESCRIPTIONS
Host Interface Pins
Serial Clock (SCL)
The SCL input is used to clock data into and out of the
X9448.
Serial Data (SDA)
SDA is a bidirectional pin used to transfer data into
and out of the device. It is an open drain output and
may be wire-ORed with any number of open drain or
open collector outputs. An open drain output requires
the use of a pull-up resistor. For selecting typical val-
ues, refer to the guidelines for calculating typical val-
ues on the bus pull-up resistors graph.
Device Address (A0 - A3)
The address inputs are used to set the least significant
4 bits of the 8-bit slave address. A match in the slave
address serial data stream must be made with the
address input in order to initiate communication with
the X9448. A maximum of 16 devices may share the
same 2-wire serial bus.
Potentiometer Pins
VH (VH0 - VH1), VL (VL0 - VL1)
The VH and VL inputs are equivalent to the terminal con-
nections on either end of a mechanical potentiometer.
VW (VW0 - VW1)
The wiper output is equivalent to the wiper output of a
mechanical potentiometer and is connected to the
inverting input of the voltage comparator.
Comparator and Device Pins
Voltage Input VNI0, VNI1
VNI0 and VNI1 are the input voltages to the plus (non-
inverting) inputs of the two comparators.
Buffered Voltage Outputs VOUT0, VOUT1
The VOUT0, and VOUT1 are the buffered voltage
comparator outputs enabled by respective bits in the
volatile analog control register.
Hardware Write Protect Input WP
The WP pin when low prevents nonvolatile writes to
the wiper counter and analog control registers.
Analog Supplies V+, V-
The analog supplies V+, V- are the supply voltages for
the XDCP analog section and the voltage comparators.
System Supply VCC and Ground VSS
The system supply VCC and its reference VSS is used
to bias the interface and control circuits.
PIN CONFIGURATION
VCC
VL0
VH0
WP
SDA
A1
1
2
3
4
5
6
7
8
9
10
24
23
22
21
20
19
18
17
16
V+
VOUT0
VNI0
NC
A0
NC
A3
SCL
NC
VNI1
SOIC
X9448
VSS
VW0
13
11
12
A2
VL1
VH1
VW1
VOUT1
VCC
VL1
VH1
WP
SDA
A2
A3
SCL
NC
VNI1
TSSOP
VSS
VW1
A1
VL0
VH0
VW0
V-
VOUT1
NC
V+
VOUT0
VNI0
A0
NC
V-
15
14
1
2
3
4
5
6
7
8
9
10
24
23
22
21
20
19
18
17
16
X9448
13
11
12
15
14
X9448
相關PDF資料 |
PDF描述 |
|---|---|
| X9448WV24I | IC DUAL PROG COMP 10K 24TSSOP |
| X9440WV24I | IC DUAL PROG COMP 10K 24TSSOP |
| X9440WS24 | IC DUAL PROG COMP 10K 64TP SO24 |
| X9448WS24-2.7 | IC DUAL PROG COMP 10K 64TP SO24 |
| CDP68HC68T1M2 | IC RTC 32X8 NVSRAM CMOS 16-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9448YP24 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Mixed Signal with 2-Wire Interface |
| X9448YP24-2.7 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Mixed Signal with 2-Wire Interface |
| X9448YP24I | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Mixed Signal with 2-Wire Interface |
| X9448YP24I-2.7 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Mixed Signal with 2-Wire Interface |
| X9448YS24 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Mixed Signal with 2-Wire Interface |
發布緊急采購，3分鐘左右您將得到回復。