參數資料
型號： X80010Q32I
廠商： INTERSIL CORP
元件分類： 電源管理
英文描述： Penta-Power Sequence Controller with Hot swap and System Management
中文描述： 5-CHANNEL POWER SUPPLY SUPPORT CKT, QCC32
封裝： 7 X 7 MM, 0.65 MM PITCH, QFN-32
文件頁數： 16/25頁
文件大?。?/td> 548K
代理商： X80010Q32I
16
FN8149.0
January 13, 2005
Overcurrent Protection (Circuit Breaker Function)
The X80010 over-current circuit provides the following
functions:
- Over-current shut-down of the power FET and external
power good indicators.
- Noise filtering of the current monitor input.
- Relaxed over-current limits for initial board insertion.
- Over-current recovery retry operation.
A sense resistor, placed in the supply path between V
EE
and
SENSE (see Figure 30) generates a voltage internal to the
X80010. When this voltage exceeds 50mV an over current
condition exists and an internal “circuit breaker” trips, turning
off the gate drive to the external FET. The actual over-
current level is dependent on the value of the current sense
resistor. For example a 20m
sense resistor sets the over-
current level to 2.5A.
Intersil’s X80010 provides a safety mechanism during
insertion of the board into the back plane. During insertion of
the board into the backplane large currents may be induced.
In order to prevent premature shut down, the overcurrent
detect circuit of the X80010 allows up to 3 times the standard
overcurrent setting during insertion.
After the PWRGD signal is asserted, the X80010 switches
back to the normal overcurrent setting. The over-current
threshold voltage during insertion is 150mV.
After the Power FET turns off due to an over-current
condition, a retry circuit turns the FET back on after a delay
of 100ms. If the over-current condition remains, the FET
again turns off. For the X80010 and X80012, this sequence
repeats indefinitely until the over-current condition is
released. For the X80011 and X80013, the X80010 retries
five times, then, sets an output signal, FAR, to indicate a
failure after retry.
Over-current shut-down
As shown in Figure 35, this circuit block contains a resistor
divider, a comparator, a noise filter and a voltage reference
to monitor for over-current conditions.
The overcurrent voltage threshold (V
OC
) is 50mV. This can
be factory set, by special order, to any setting between
30mV and 100mV. V
OC
is the voltage between the SENSE
and V
EE
pins and across the R
SENSE
resistor. If the
selected sense resistor is 20mW, then 50mV corresponds to
an overcurrent of 2.5A.
If an over-current condition is detected, the GATE is turned
off and all power good indicators go inactive.
Overcurrent Noise Filter
The X80010 has a noise (low pass) filter built into the over-
current comparator. The comparator will thus require the
current spikes to exceed the overcurrent limit for more than
5μs.
Overcurrent During Insertion
Insertion is defined as the first plug-in of the board to the
backplane. In this case, the X80010 is initially fully powered
off prior to the hot plug connection to the mains supply. This
condition is different from a situation where the mains supply
has temporarily failed resulting in a partial recycle of the
power. This second condition will be referred to as a power
cycle.
During insertion, the board can experience high levels of
current for short periods of time as power supply capacitors
charge up on the power bus. To prevent the over-current
sensor from turning off the FET inadvertently, the X80010
has the ability to allow more current to flow through the
powerFET and the sense resistor for a short period of time
until the FET turns on and the PWRGD signal goes active. In
the X80010, 150mV is allowed across sense resistor the
during insertion (10A assuming a 20m
resistor). This
provides a mechanism to reduce insertion issues associated
with huge current surges.
Overcurrent/
Short-Circuit
Retry Logic
Gate
Control
Bl
ock
RETRY
Delay
Voltage
Reference
5μs
noise
filtering
38R
3R
+
–
-48V
Overcurrent Event
R
Sense
FIGURE 35. OVERCURRENT DETECTION/SHORT CIRCUIT
PROTECTION
X80010, X80011, X80012, X80013
相關PDF資料
PDF描述
X80013Q32I Connector Wall Plate; Color:Almond; Leaded Process Compatible:Yes; Contact Termination:IDC; No. of Ports:3 RoHS Compliant: Yes
X80011Q32I Penta-Power Sequence Controller with Hot swap and System Management
X80010 Penta-Power Sequence Controller with Hot swap and System Management
X80011 Penta-Power Sequence Controller with Hot swap and System Management
X80012 Penta-Power Sequence Controller with Hot swap and System Management
相關代理商/技術參數
參數描述
X80011 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Penta-Power Sequence Controller with Hot swap and System Management
X80011Q32I 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Penta-Power Sequence Controller with Hot swap and System Management
X80012 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Penta-Power Sequence Controller with Hot swap and System Management
X80012Q32I 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Penta-Power Sequence Controller with Hot swap and System Management
X80013 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Penta-Power Sequence Controller with Hot swap and System Management
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*