參數資料
型號： X40235
英文描述： Integrated System Management IC Triple Voltage Monitors, POR, 2 kbit EEPROM Memory, and Single/Dual DCP(帶2K EEPROM和單/雙數字電位器的三路電壓監控器)
中文描述： 綜合系統管理IC三電壓監測器，葡萄牙，2千比特的EEPROM內存，單/雙副處長（帶2K的EEPROM和單/雙數字電位器的三路電壓監控器）
文件頁數： 12/39頁
文件大?。?/td> 215K
代理商： X40235
X4023x
– Preliminary Information
Characteristics subject to change without notice.
12 of 39
REV 1.0.4 7/12/01
www.xicor.com
A nonvolatile write to a DCP will change the “wiper
position” by simultaneously writing new data to the
associated WCR and NVM. Therefore, the new “wiper
position” setting is recalled into the WCR after V
CC
of
the X4023x is powered down and then powered back
up.
A volatile write operation to a DCP however, changes
the “wiper position” by writing new data to the associ-
ated WCR only. The contents of the associated NVM
register remains unchanged. Therefore, when V
CC
to
the device is powered down then back up, the “wiper
position” reverts to that last position written to the DCP
using a nonvolatile write operation.
Both volatile and nonvolatile write operations are exe-
cuted using a three byte command sequence: (DCP)
Slave Address Byte, Instruction Byte, followed by a
Data Byte (See Figure 9)
A DCP Read operation allows the user to “read out” the
current “wiper position” of the DCP, as stored in the
associated WCR. This operation is executed using the
Random Address Read command sequence, consist-
ing of the (DCP) Slave Address Byte followed by an
Instruction Byte and the Slave Address Byte again
(Refer to Figure 10).
Instruction Byte
While the Slave Address Byte is used to select the
DCP devices, an Instruction Byte is used to determine
which DCP is being addressed.
The Instruction Byte (Figure 8) is valid only when the
Device Type Identifier and the Internal Device Address
bits of the Slave Address are set to 1010111. In this
case, the two Least Significant Bit’s (I1 - I0) of the
Instruction Byte are used to select the particular DCP
(0 - 2). In the case of a Write to any of the DCPs (i.e.
the LSB of the Slave Address is 0), the Most Significant
Bit of the Instruction Byte (I7), determines the Write
Type (WT) performed.
If WT is “1”, then a Nonvolatile Write to the DCP
occurs.
In this case, the “wiper position” of the DCP is changed
by simultaneously writing new data to the associated
WCR and NVM. Therefore, the new “wiper position”
setting is recalled into the WCR after V
CC
of the
X4023x has been powered down then powered back
up
If WT is “0” then a DCP Volatile Write is performed. This
operation changes the DCP “wiper position” by writing
new data to the associated WCR only. The contents of
Figure 7.
DCP Power up
t
V
CC
V
TRIP1
V
CC (Max.)
t
PURST
Maximum Wiper Recall time
0
t
TRANS
WT
Description
0
Select a Volatile Write operation to be performed
on the DCP pointed to by bits P1 and P0
1
Select a Nonvolatile Write operation to be per-
formed on the DCP pointed to by bits P1 and P0
0
0
WT
0
0
0
P1
P0
WRITE TYPE
DCP SELECT
This bit has no effect when a Read operation is being performed.
I5
I6
I7
I4
I3
I2
I1
I0
Figure 8.
Instruction Byte Format
相關PDF資料
PDF描述
X40237 Integrated System Management IC Triple Voltage Monitors, POR, 2 kbit EEPROM Memory, and Single/Dual DCP(帶2K EEPROM和單/雙數字電位器的三路電壓監控器)
X40239 Integrated System Management IC Triple Voltage Monitors, POR, 2 kbit EEPROM Memory, and Single/Dual DCP(帶2K EEPROM和單/雙數字電位器的三路電壓監控器)
x40410(中文) 4kbit EEPROM Dual Voltage Monitor with Integrated CPU Supervisor(4K位EEPROM 雙電壓監測的CPU監控器)
X40420(中文) Dual Voltage Monitor with Intergrated CPU Supervisor
X40421(中文) Dual Voltage Monitor with Intergrated CPU Supervisor
相關代理商/技術參數
參數描述
X40235S16I-A 功能描述:IC VOLTAGE MON TRPL EE 16-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件
X40235S16I-AT1 功能描述:IC VOLTAGE MON TRPL EE 16-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件
X40235S16I-B 功能描述:IC VOLTAGE MON TRPL EE 16-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件
X40235S16I-BT1 功能描述:IC VOLTAGE MON TRPL EE 16-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件
X40237 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Triple Voltage Monitors, POR, 2 kbit EEPROM MEMORY, and Single/Dual DCP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*