參數資料
型號： WEDPNF8M722V-1010BI
廠商： MICROSEMI CORP-PMG MICROELECTRONICS
元件分類： 存儲器
英文描述： SPECIALTY MEMORY CIRCUIT, PBGA275
封裝： 32 X 25 MM, PLASTIC, BGA-275
文件頁數： 14/43頁
文件大小： 1280K
代理商： WEDPNF8M722V-1010BI
21
2 1
White Electronic Designs Corporation (602) 437-1520 www.whiteedc.com
White Electronic Designs
WEDPNF8M722V-XBX
UNLOCK BYPASS COMMAND SEQUENCE
The unlock bypass feature allows the system to program
bytes or words to the device faster than using the standard
program command sequence. The unlock bypass com-
mand sequence is initiated by first writing two unlock cycles.
This is followed by a third write cycle containing the unlock
bypass command, 20h. The device then enters the unlock
bypass mode. A two-cycle unlock bypass program com-
mand sequence is all that is required to program in this
mode. The first cycle in this sequence contains the unlock
bypass program command, A0h; the second cycle con-
tains the program address and data. Additional data is pro-
grammed in the same manner. This mode dispenses with
the initial two unlock cycles required in the standard pro-
gram command sequence, resulting in fast total program-
ming time. Table 7 shows the requirements for the com-
mand sequence.
During the unlock bypass mode, only the Unlock Bypass
Program and Unlock Bypass Reset commands are valid. To
exit the unlock bypass mode, the system must issue the
two-cycle unlock bypass reset command sequence. The
first cycle must contain the data 90h; the second cycle the
data 00h. Addresses are “don't care” for both cycles. The
device then returns to reading array data.
Figure 6 illustrates the algorithm for the program operation.
See the Erase/Program Operations table in the “Flash AC
Characteristics” for parameters, and to Figure 12 for timing
diagrams.
AUTOSELECT COMMAND SEQUENCE
The autoselect command sequence allows the host sys-
tem to determine whether or not a sector is protected. Table
7 shows the address and data requirements. This method
is an alternative to that shown in Table 6, which is intended
for PROM programmers and requires VID on address bit FA9.
The autoselect command sequence is initiated by writing
two unlock cycles, followed by the autoselect command.
The device then enters the autoselect mode, and the sys-
tem may read at any address any number of times, without
initiating another command sequence.
A read cycle containing a sector address (SA) and the ad-
dress 02h in word mode (or 04h in byte mode) returns
02h in that sector is protected, or 00h if it is unprotected.
Refer to Table 5 for valid sector addresses.
The system must write the reset command to exit autoselect
mode and return to reading array data.
相關PDF資料
PDF描述
WME128K8-150CC 128K X 8 EEPROM 5V, 150 ns, CDIP32
WME128K8-150DEIA 128K X 8 EEPROM 5V, 150 ns, CDSO32
WMF128K8-120FFQ5A 128K X 8 FLASH 5V PROM, 120 ns, CDFP32
WMF128K8-70CQ5 128K X 8 FLASH 5V PROM, 70 ns, CDIP32
WMF128K8-70FFI5A 128K X 8 FLASH 5V PROM, 70 ns, CDFP32
相關代理商/技術參數
參數描述
WEDPNF8M722V-1010BM 制造商:WEDC 制造商全稱:White Electronic Designs Corporation 功能描述:8Mx72 Synchronous DRAM + 16Mb Flash Mixed Module Multi-Chip Package
WEDPNF8M722V-1012BC 制造商:WEDC 制造商全稱:White Electronic Designs Corporation 功能描述:8Mx72 Synchronous DRAM + 16Mb Flash Mixed Module Multi-Chip Package
WEDPNF8M722V-1012BI 制造商:WEDC 制造商全稱:White Electronic Designs Corporation 功能描述:8Mx72 Synchronous DRAM + 16Mb Flash Mixed Module Multi-Chip Package
WEDPNF8M722V-1012BM 制造商:WEDC 制造商全稱:White Electronic Designs Corporation 功能描述:8Mx72 Synchronous DRAM + 16Mb Flash Mixed Module Multi-Chip Package
WEDPNF8M722V-1015BC 制造商:WEDC 制造商全稱:White Electronic Designs Corporation 功能描述:8Mx72 Synchronous DRAM + 16Mb Flash Mixed Module Multi-Chip Package
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*