參數資料
型號： W19B320ABB7G
廠商： WINBOND ELECTRONICS CORP
元件分類： PROM
英文描述： 2M X 16 FLASH 3V PROM, 70 ns, PBGA48
封裝： 6 X 8 MM, 0.80 MM PITCH, TFBGA-48
文件頁數： 5/53頁
文件大?。?/td> 479K
代理商： W19B320ABB7G
W19B320AT/B
Publication Release Date: December 27, 2005
- 13 -
Revision A4
6.2.3
AUTOSELECT Command Sequence
The AUTOSELECT command sequence provides the host system to access the manufacturer and
device codes, and determine whether a sector is protected or not. This is an alternative method, which
is intended for PROM programmers and requires VID on address pin A9. The AUTOSELECT
command sequence may be written to an address within a bank that is either in the read or erase-
suspend-read mode. When the device is actively programming or erasing in the other bank, the
AUTOSELECT command may not be written.
The first writing two unlock cycles initiate the AUTOSELECT command sequence. This is followed by
a third write cycle that contains the bank address and the AUTOSELECT command. The bank then
enters into the AUTOSELECT mode. The system may read at any address within the same bank
without initiating another AUTOSELECT command sequence:
A read cycle at address (BA) XX00h (where BA is
the bank address) returns the manufacturer code.
A read cycle at address (BA) XX01h in word mode
(or (BA) XX02h in byte mode) returns the device
code.
A read cycle to an address containing a sector ad
dress (SA) within the same bank, and the address
02h on A7-A0 in word mode (or the address 04h on A6-A-1 in byte mode) returns 01h if the
sector is protected or 00h if it is unprotected.
To return to read mode (or erase-suspend-read mode if the bank was previously in Erase Suspend),
the system must write the reset command.
Enter Security Sector/Exit Security Sector Command Sequence
The Security Sector region provides a secured data area containing a random, sixteen-byte electronic
serial number (ESN). The system can access the Security Sector region by issuing the three-cycle
Enter Security Sector command sequence. The device continues to access the Security Sector region
until the system issues the four-cycle Exit Security Sector command sequence. The Exit Security
Sector command sequence returns the device to normal operation. See “Security Sector Flash
Memory Region” for further information.
6.2.4
Byte/Word Program Command Sequence
The device can be programmed either by word or byte, which depending on the state of the #BYTE
pin. Programming is a four-bus-cycle operation. The program command sequence is initiated by
writing two unlock write cycles, followed by the program setup command. The program address and
data are written next, which in turn initiate the Embedded Program algorithm. The device automatically
provides internally generated program pulses and verifies the programmed cell margin.
Once the Embedded Program algorithm is complete, the bank then returns to the read mode and
addresses are no longer latched. The system can determine the status of the program operation by
using DQ7, DQ6, or RY/#BY. Please refer to the Write Operation Status section for bits' information.
Any commands written to the device during the Embedded Program Algorithm are ignored. Please
note that a hardware reset will immediately stop the program operation. The program command
sequence should be reinitiated when the bank has returned to the read mode, in order to ensure data
integrity.
Programming is allowed in any sequence and across sector boundaries. A bit cannot be programmed
from “0” back to “1.” If trying to do so may cause that bank to set DQ5 = 1, or cause the DQ7 and DQ6
status bits to indicate that the operation is successful. However, a succeeding read will show that the
data is still “0.” Only erase operations can change “0” to “1.”
相關PDF資料
PDF描述
W19B320ATT7M 2M X 16 FLASH 3V PROM, 70 ns, PDSO48
W3DG6416V10D1 16M X 64 SYNCHRONOUS DRAM MODULE, ZMA144
W3EG7266S265D3 64M X 72 DDR DRAM MODULE, 0.75 ns, DMA184
WED3EG72M32S403JD3GG 32M X 72 DDR DRAM MODULE, 0.7 ns, DMA184
WED9LAPC2C16P8BI 4M X 32 SYNCHRONOUS DRAM, PBGA153
相關代理商/技術參數
參數描述
W19B320ABB7H 功能描述:IC FLASH 32MBIT 70NS 48TFBGA RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:1,000 系列:- 格式 - 存儲器:RAM 存儲器類型:移動 SDRAM 存儲容量:256M（8Mx32） 速度:133MHz 接口:并聯 電源電壓:1.7 V ~ 1.95 V 工作溫度:-40°C ~ 85°C 封裝/外殼:90-VFBGA 供應商設備封裝:90-VFBGA（8x13） 包裝:帶卷 (TR) 其它名稱:557-1327-2
W19B320ABT7H 功能描述:IC FLASH 32MBIT 70NS 48TSOP RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:1,000 系列:- 格式 - 存儲器:RAM 存儲器類型:移動 SDRAM 存儲容量:256M（8Mx32） 速度:133MHz 接口:并聯 電源電壓:1.7 V ~ 1.95 V 工作溫度:-40°C ~ 85°C 封裝/外殼:90-VFBGA 供應商設備封裝:90-VFBGA（8x13） 包裝:帶卷 (TR) 其它名稱:557-1327-2
W19B320ATB 制造商:WINBOND 制造商全稱:Winbond 功能描述:4M × 8/2M × 16 BITS 3V FLEXIBLE BANK FLASH MEMORY
W19B320ATB7H 功能描述:IC FLASH 32MBIT 70NS 48TFBGA RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:1,000 系列:- 格式 - 存儲器:RAM 存儲器類型:移動 SDRAM 存儲容量:256M（8Mx32） 速度:133MHz 接口:并聯 電源電壓:1.7 V ~ 1.95 V 工作溫度:-40°C ~ 85°C 封裝/外殼:90-VFBGA 供應商設備封裝:90-VFBGA（8x13） 包裝:帶卷 (TR) 其它名稱:557-1327-2
W19B320ATT7H 功能描述:IC FLASH 32MBIT 70NS 48TSOP RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:1,000 系列:- 格式 - 存儲器:RAM 存儲器類型:移動 SDRAM 存儲容量:256M（8Mx32） 速度:133MHz 接口:并聯 電源電壓:1.7 V ~ 1.95 V 工作溫度:-40°C ~ 85°C 封裝/外殼:90-VFBGA 供應商設備封裝:90-VFBGA（8x13） 包裝:帶卷 (TR) 其它名稱:557-1327-2
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*