參數資料
型號： VSC837
廠商： Vitesse Semiconductor Corporation.
英文描述： 3.2Gb/s 68x68 Crosspoint Switch
中文描述： 達3.2GB / s的68x68交叉點開關
文件頁數： 3/26頁
文件大小： 340K
代理商： VSC837
VITESSE
Preliminary Data Sheet
VSC837
3.2Gb/s
68x68 Crosspoint Switch
G52309-0, Rev 3.0
02/16/01
Page 3
VITESSE
SEMICONDUCTOR CORPORATION
741 Calle Plano
Camarillo, CA 93012
Tel: (800) VITESSE
FAX: (805) 987-5896
Email: prodinfo@vitesse.com
Internet: www.vitesse.com
Programming Interface
Parallel Mode
In parallel mode (SERIAL=0, BURST=0), the binary word on INCHAN[6:0] is the numerical identifier of
the input that will be routed to the specified output. OUTCHAN[6:0] is the numerical identifier of the output
being programmed. A rising edge on the LOAD signal will transfer the programming data to the shadow regis-
ter in the program memory. Raising CONFIG (asynchronously) will transfer the programming data to the main
latches in the program memory and cause the internal select signals in the core to re-configure the multiplexer.
Lowering CONFIG will latch the main latches. CONFIG may be tied HIGH to enable programming take effect
instantaneously.
This interface may be used with multiplexed address/data buses by using only INCHAN[6:0] without
OUTCHAN[6:0] and dropping ALE when the address of the output to be programmed is present on
INCHAN[6:0]. After the address is latched, the input address may be presented on INCHAN[6:0] and pro-
gramming proceeds as above.
No read-back capability is provided in parallel mode. Read-back for diagnostic purposes is provided in
serial mode via the scan function.
Serial Mode
In serial mode (SERIAL=1, BURST=0), the INCHAN0 pin becomes the serial data input and the
INCHAN1 pin becomes the serial clock (rising edge triggered). A serial word of the form [Output][Input] is
shifted into the internal shift register, and the LOAD pin is asserted (HIGH) coincident with the last bit of the
data word to signal that the word is to be applied. This transfers the input identifier to the shadow register of the
addressed output. CONFIG is then applied (asynchronously) to transfer one or more program commands to the
main latches of the program memories.
The SDOUT pin follows the data on the INCHAN0_SDIN pin 14 clock cycles later. This enables the user
to chain the serial ports of several crosspoints, shift program data for all switches through such a chain, and
assert LOAD on all switches simultaneously to program all of the connections simultaneously.
The output field is 7 bits long, representing the binary numerical identifier of the output to be programmed.
The input field is 7 bits long, representing the numerical identifier of the input that will be routed to the speci-
fied output.
Serial Read-Back
Read-back of the program memory contents is accomplished in serial mode by setting the ALE_SCN pin
HIGH. This will serially shift out the contents of the main latches in the program memories, slice 68 first and
slice 0 last, and MSB-first, LSB-last for each 7-bit word. One rising edge of INCHAN1_SCLK with
ALE_SCN=0 and SERIAL=1 must occur to load the entire 483-bit shift register prior to shifting out data. At a
clock rate of 66MHz, this operation takes 7.26
μ
s.
相關PDF資料
PDF描述
VSC837UG DIODE ZENER SINGLE 150mW 3Vz 5mA-Izt 0.0667 10uA-Ir 1 SOT-523 3K/REEL
VSC838UG RECTIFIER BRIDGE 25A 200V 300A-ifsm 1.1V-vf 5uA-ir GBPC 100/TRAY
VSC838 3.2Gb/s 36x37 Crosspoint Switch
VSC8476 XAUI to XFI 10GE & 10GFC Transceiver
VSC8486 10 Gbps XAUI or XGMII to XFI LAN/WAN Transceiver
相關代理商/技術參數
參數描述
VSC837UG 制造商:Vitesse Semiconductor Corporation 功能描述:
VSC838 制造商:VITESSE 制造商全稱:Vitesse Semiconductor Corporation 功能描述:3.2Gb/s 36x37 Crosspoint Switch
VSC838UG 制造商:VITESSE 制造商全稱:Vitesse Semiconductor Corporation 功能描述:3.2Gb/s 36x37 Crosspoint Switch
VSC8476 制造商:VITESSE 制造商全稱:Vitesse Semiconductor Corporation 功能描述:XAUI to XFI 10GE & 10GFC Transceiver
VSC8479 制造商:VITESSE 制造商全稱:Vitesse Semiconductor Corporation 功能描述:9.95 Gbps to 11.3 Gbps 16-bit Transceiver
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*