- 您現在的位置：買賣IC網 > PDF目錄202515 > VNC1L-1A (Future Technology Devices International Ltd) PDF資料下載
參數資料
| 型號： | VNC1L-1A |
| 廠商： | Future Technology Devices International Ltd |
| 元件分類： | 總線控制器 |
| 中文描述： | UNIVERSAL SERIAL BUS CONTROLLER, PQFP48 |
| 封裝： | 7 X 7 MM, 0.50 MM PITCH, GREEN, LQFP-48 |
| 文件頁數： | 6/32頁 |
| 文件大?。?/td> | 672K |
| 代理商： | VNC1L-1A |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
Copyright 2009 Future Technology Devices International Limited
14
Document Reference No.: FT_000030
Vinculum VNC1L Embedded USB Host Controller IC Datasheet Version 2.02
Clearance No.: FTDI# 50
5 Firmware Control Interface
There are three firmware interface options for the command monitor on the combined control and data
interface. The command monitor interface options are UART, FIFO or SPI. The mode of operation is
selected using VNC1L pins 46 and 47.The pin connections used to select the mode of the interface are
shown in Table 5.1:
Pin No.
Mode
47
(ACBUS6)
46
(ACBUS5)
Pull-Up
UART
Pull-Up
Pull-Down
SPI
Pull-Down
Pull-Up
FIFO
Pull-Down
UART
Table 5.1 Combined Interface Selection
Important : Pins ACBUS5 and ACBUS6 should not be tied directly to GND or VCC.
Pins ACBUS5 and ACBUS6 should be pulled high or low using a resistor of around 47k. These pins are
read only at reset, but may then become outputs after the interface choice has been selected. When FIFO
mode is selected ACBUS5 will be used as an output by VNC1L Firmware.
5.1 UART Interface
When the data and control buses are configured in UART mode, the interface implements a standard
asynchronous serial UART port with flow control. The UART can support baud rates from 300baud to
1Mbaud.
Data transfer uses NRZ (Non-Return to Zero) data format consisting of 1 start bit, 7 or 8 data bits, an
optional parity bit, and one or two stop bits. When transmitting the data bits, the least significant bit is
transmitted first. Transmit and receive waveforms are illustrated in Figure 5.1 and Figure 5.2:
.
Figure 5.1 UART Receive Waveform
Figure 5.2 UART Transmit Waveform
Baud rate (default =9600 baud), flow control settings (default = RTS/CTS), number of data bits
(default=8), parity (default is no parity) and number of stop bits (default=1) are all configurable using
the firmware command interface. Please refer to http://www.ftdichip.com (or latest version).
相關PDF資料 |
PDF描述 |
|---|---|
| VND5E012AYTR-E | SPECIALTY ANALOG CIRCUIT, PDSO36 |
| VNL5050S5-E | POWER SUPPLY SUPPORT CKT, PDSO8 |
| VNL5050N3TR-E | POWER SUPPLY SUPPORT CKT, PDSO3 |
| VO27.0000000M0000001 | VCXO, CLOCK, 27 MHz, TTL OUTPUT |
| VP06DDC1R0N999 | 0.3 W, SMPS TRANSFORMER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| VNC1L-1A-REEL | 功能描述:USB 接口集成電路 USB Vinculum Host /Dev Ctrl IC LQFP-48 RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| VNC1L-1A-TRAY | 功能描述:USB 接口集成電路 USB Vinculum Host /Dev Ctrl IC LQFP-48 RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| VNC2 | 制造商:FTDI 制造商全稱:FTDI 功能描述:VNC2 Debug Module |
| VNC2 DEBUG MODULE | 功能描述:界面開發工具 USB Vinculum-II Debug/Programmer Mod RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| VNC214B-15A-1D | 制造商:SMC Corporation of America 功能描述:Valve, media, solenoid, body port, 1/2 inch |
發布緊急采購，3分鐘左右您將得到回復。